Publicité
Les langues disponibles
Les langues disponibles
O
F
A
6 U
R
NE
OR
LL
NIVERSAL
EMOTE
All manuals and user guides at all-guides.com
P
M
ROGRAMMING A
ACRO ON A
D
K
EVICE
EY
In its default state, when you press a
device key (e.g., TV) on the One For
All 6L Universal Remote Control
(URC-6020 B00), the remote will
switch to that selected device.
However, you can also program a
Macro onto the Device keys to allow
for additional functionality. For
example, if your devices are
connected to a receiver unit, you can
program a Device macro to switch the
receiver's input to the selected device.
To Program the Device Key Macro
For example, let's assume that your
DVD in connected to Input 3 of your
receiver. You can program a macro
that will switch the receiver's input to
input 3 when you press and hold the
DVD key.
1.
Press and hold SET until the LED
(red light) blinks twice, then
release SET.
2.
Enter 9 9 5. The LED will blink
twice.
3.
Press the DVD key once.
4.
Press the AUD key (to select the
receiver)
Press digit 3 (for the input), and
5.
press DVD (to return control to
the DVD key).
6.
To save the settings and exit the
program, press and hold SET
until the LED blinks twice, then
release SET.
NOTE: You can program up to 20
functions on the Device Key Macro.
You can program a device Key Macro
onto any device key.
To Operate the Device Key Macro
1.
After programming, point the
remote control at the receiver
and press the DVD key for at least
2 seconds. This will switch the
Receiver's input to input 3, to
allow you to view the DVD.
NOTE: When you press the device key
(e.g., DVD) for less than 2 seconds, the
remote will only select the DVD mode
but will not change the Input on the
receiver. This allows you to still change
modes while using the remote.
NOTE: After executing the Device Key
Macro, the remote will return to the
DVD mode, to allow the control of the
DVD device.
10
Using Channel Scan
C
ONTROL
C
M
LEARING A
ACRO
1.
Press and hold SET until the LED
(red light) blinks twice, then
release SET.
2.
Enter 9 9 5. The LED will blink
twice.
3.
Select a macro key (e.g., M1, M2,
POWER or any device key) you
want to clear and press it once.
Press and hold SET until the LED
4.
blinks twice, then release SET.
The macro is now deleted but
the keys (in the case of POWER
and device keys), will retain
their original function.
USING CHANNEL SCAN
In the TV, VCR, DVD and CBL/SAT
modes, use the FAV key to start a 3-
second scan of all favorite channels (if
programmed, "Programming
Favorite Channel Scan" on page 10)
and/or all channels for the selected
mode.
1.
Press TV, VCR, DVD or CBL/SAT
once.
2.
Press FAV once.
•
If Favorite Channel Scan
has been set up, scanning
of favorite channels will
start and cycle through
stored channels, then
proceed to the next channel
up and cycle through all
channels on the selected
device.
•
If Favorite Channel Scan
has not been set up,
scanning will start with the
current channel, then
proceed to the next channel
up and cycle through all
channels on the selected
device.
3.
To stop scanning channels at any
time, press any key once.
PROGRAMMING
FAVORITE CHANNEL
SCAN
In the TV, VCR, DVD or CBL/SAT mode,
you can store a list of up to 10 favorite
channels, in any order, that will be
immediately scanned when you press
Publicité
