Makita DHW080 Manuel D'instructions page 20

5. Put the high pressure washer onto the container
so that it is secured with the mounts on the lid of the
container.
► Fig.35: 1. High pressure washer 2. Lid 3. Air bleed-
ing hole
NOTE: If water suction does not work, it takes a long
time, or the water pressure is not enough, check the
following:
• Loosening of the hose assembly, strainer
assembly, and water hose connector.
• Coupling sleeves of the hose assembly are
firmly attached onto the water hose connector
and filter case of the strainer assembly.
Tighten if they are loose.
Hose assembly
► Fig.36: 1. Coupling sleeve
Strainer assembly
► Fig.37: 1. Hose band 2. Filter case
Water hose connector
► Fig.38: 1. Water hose connector
NOTICE:
Pay attention to the handling of the
container when carrying. Carrying the container
with high pressure washer and accessories or water
inside may cause accident or personal injury due to
its own weight.
NOTICE:
When carrying the container, do not
shake, turnover, or lean it excessively. Doing so
may cause;
— the water inside spilled out;
— the high pressure washer on the lid dropped off
from the container or;
— the rotation of the container's wheels hindered.
NOTICE:
When carrying the container by the
handle, water may spill out if there is plenty of
water inside.
NOTICE:
Water may come out from the air
bleeding hole if the water inside reaches to the air
bleeding hole by tilting the container.
NOTICE:
Do not step on the container. The lid
may be broken.
NOTICE:
Do not leave the container filled with
water for a long time. Doing so may cause the con-
tainer damaged and result in water leakage.
After use, follow the procedure below:
1. Remove the cap on the drain outlet and discharge
water.
► Fig.39: 1. Drain outlet
2.
Wipe off the moisture inside of the container using
a cloth and then dry the container completely.
NOTICE:
Do not store the high pressure washer
and the accessories while the inside of the con-
tainer is wet. Remaining moisture may cause mal-
function and rust.
MAINTENANCE & STORAGE
CAUTION:
Always be sure that the tool is
switched off and battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning the nozzle
Use the cleaner pin to remove dirt from or unclog the nozzle.
► Fig.40: 1. Cleaner pin
NOTE: To maintain the optimal performance, clean
the nozzle periodically.
NOTICE:
Do not remove dirt or debris forcibly.
This may result in personal injury or damage to the
ejection hole causing deviated jet angles or poor
performance.
Cleaning the filter
Detach the water hose connector and remove dirt and
debris from the inside of the filter.
► Fig.41: 1. Water hose connector 2. Filter 3. Sealing ring
When using the strainer assembly, take the filter out of
the filter case and remove dirt and debris.
► Fig.42: 1. Filter 2. Filter case
NOTE: To maintain the optimal performance, clean
the filter periodically.
Storage
CAUTION:
Always store in an indoor location
where the temperature does not go below freez-
ing. If the high pressure washer freezes and malfunc-
tions, contact your local service center for repairs.
Store the accessories in the side pocket of the high
pressure washer.
Storage example
► Fig.43: 1. High-pressure hose 2. Nozzle 3. Trigger gun
If your model is supplied with the container, store the
high pressure washer and accessories in it.
Storage example
► Fig.44: 1. High pressure washer 2. Nozzle
3. Trigger gun 4. Washing brush 5. Foam
nozzle 6. Charger 7. Hose assembly
8. Strainer assembly
NOTE: Some accessories shown in the illustra-
tion are supplied as optional accessories in some
countries.
20 ENGLISH