Télécharger Imprimer la page

Makita DF010DSP Manuel D'instructions page 6

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 8
ASSEMBLY
CAUTION:
• Always be sure that the lock button is in the locked
position B and the battery cartridge is removed before
carrying out any work on the tool.
Installing or removing driver bit or socket bit
(Fig. 9, 10 & 11)
Use only the driver bit or socket bit shown in the figure.
Do not use any other driver bit or socket bit.
For European and North & South American
countries, Australia and New Zealand
Use only these type of bit. Follow the
A=12mm
procedure (1).
B=9mm
(Note) Bit-piece is not necessary.
006348
For other countries
To install these types of bits, follow the
A=17mm
procedure (1).
B=14mm
(Note) Makita bits are these types.
To install these types of bits, follow the
A=12mm
procedure (2).
B=9mm
(Note) Bit-piece is necessary for installing
the bit.
006349
1.
To install the bit, pull the sleeve in the direction of the
arrow and insert the bit into the sleeve as far as it
will go. Then release the sleeve to secure the bit.
2.
To install the bit, pull the sleeve in the direction of the
arrow and insert the bit-piece and bit into the sleeve
as far as it will go. The bit-piece should be inserted
into the sleeve with its pointed end facing in. Then
release the sleeve to secure the bit.
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out firmly.
NOTE:
• If the bit is not inserted deep enough into the sleeve,
the sleeve will not return to its original position and the
bit will not be secured. In this case, try re-inserting the
bit according to the instructions above.
OPERATION
The tool can be used in two ways; a straight type and a
pistol type which is selectable according to the conditions
of workplace and screwdriving. (Fig. 12)
Screwdriving operation (Fig. 13)
CAUTION:
• Adjust to the proper torque level for your work.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Then switch the tool on. When
the clutch cuts in, the motor will stop automatically. Then
release the switch.
6
All manuals and user guides at all-guides.com
MAINTENANCE
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
OPTIONAL ACCESSORIES
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Adjust grip
• Drill bits
• Screw bits
• Socket bits
• Bit piece
• Makita genuine battery and charger
• Plastic carrying case
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN60745:
The noise level under working may exceed 80 dB (A).
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
CAUTION:
CAUTION:
CAUTION:
Sound pressure level (L
) : 70 dB (A) or less
pA
Uncertainty (K) : 3 dB (A)
Wear ear protection
Work mode: drilling into metal
Vibration emission (a
) : 2.5 m/s
h, D
2
Uncertainty (K) : 1.5 m/s
ENG905-1
ENG900-1
2
or less

Publicité

loading