Joovy Twin Roo+ Mode D'emploi page 3

• Locate the rear wheel assembly and slide it onto the rear legs with the brakes facing the rear of the stroller. Be sure to slide each side all
the way in until the push pins are engaged. See Figure 3.1.
NOTE: You may need to push each of the push pins in to slide the assembly into place.
• Pull upward on each side of the rear axle to ensure it is installed properly.
4 Installing Front Wheels
• Place the front wheel sets onto the front wheel posts until they click in place. See Figure 4.1.
• Pull on the wheel sets to ensure they are installed properly.
5 Front Wheel Locks
The front wheels can be set to swivel or lock.
• To lock the front wheels, rotate each wheel set so that it points forward.
• Pull up on the red locking lever to engage the swivel lock. See Figure 5.1.
• To unlock the wheels (swivel mode) push down on the lever.
6 Rear Wheel Brakes
• Always engage rear brakes before placing an infant car seat or removing an infant car seat from the stroller.
• To engage the brakes, push down on BOTH of the red brake levers until the brake snaps in place. See Figure 6.1.
• Check that BOTH wheel brakes are properly engaged.
• To release the brakes, lift up on BOTH brake levers. See Figure 6.2.
Always make sure BOTH wheel brakes are engaged when stroller is not being pushed so that the stroller will not roll
away. Never leave stroller unattended, especially on a hill or incline, as the stroller may tip over or slide.
7 Installing the Infant Car Seat Adapters and Car Seats (Sold Separately)
This stroller is compatible with UPPAbaby® MESA, Britax® B-Safe, BOB® B-Safe and Graco® Click Connect infant car seats. Identify the
infant car seat adapters and follow its instruction below. You can mix and match the car seats and the car seat can face the same direction
or opposite directions.
UPPAbaby® MESA
• To install the UPPAbaby® car seat adapters make sure that the ends with the slot are facing down (See Figure 7.1) and that the sides
with the release tabs are facing out. See Figure 7.2.
• Push the car seat adapters down into the brackets until they click into place. See Figure 7.3.
• Pull upward on each adapter to ensure it is secure.
• Lower the car seat onto the car seat adapters until it clicks into place. See Figure 7.4. The car seat can face the left or right.
• Pull upward on the car seat to ensure it is secure.
• Only use with the handle in the UP position. See Figure 7.4a.
• To remove the seat, push the button found on the handle center and lift the car seat up.
Britax® B-Safe and BOB® B-Safe
• To install the Britax® B-Safe/BOB® B-Safe car seat adapters make sure that the ends with the slot are facing down (See Figure 7.5) and
that the sides with the release tabs are facing out. See Figure 7.2.
• Push the car seat adapters down into the brackets until they click into place. See Figure 7.6.
• Pull upward on each adapter to ensure it is secure.
• Lower the car seat onto the car seat adapters until it clicks into place. The car seat can face the left or right.
• Pull upward on the car seat to ensure it is secure.
• To remove the seat, pull up on the buttons found under both side of handle and lift the car seat up. See Figure 7.7.
Graco® Click Connect
• To install the Graco® Click Connect car seat adapters make sure that the ends with the slot are facing down. See Figure 7.8. Then pair up
2 correct adapters. See Figure 7.9. Then make sure the release tabs are facing out. See Figure 7.10 and 7.11.
• Push the car seat adapters down into the brackets until they click into place. The arrows on these parts should face the same direction
when installed.
• Pull upward on each adapter to ensure it is secure.
• Lower the car seat onto the car seat adapters until it clicks into place. The car seat will face the direction that the arrows are pointing.
See Figure 7.12.
• Pull upward on the car seat to ensure it is secure.
• To remove the seat, pull up on the same button that is used to remove the car seat from the base.
All manuals and user guides at all-guides.com
WARNING
!
EN FR ES