Sony CDX-L300 Installation/Connexions

FM /AM
Compact Disc
Player
Inst allat ion/Connect ions
Inst allat ion/Connexions
CDX-L300
Sony Corporation © 2002
1
1
4
Equipm ent used in illust rat ions (not supplied)
Appareils ut ilisés dans les illust rat ions (non fournis)
Front speaker
Haut-parleur frontal
Rear speaker
Haut-parleur arrière
Downloaded from: https://www.usersmanualguide.com/
3-237-525-11 (1)
Printed in Korea
2 3
× 4
× 2
5 6
Pow er amplifier
Amplificateur de puissance
2
A
B
AUDIO OUT
Part s Iist (1)
The numbers in the list are keyed to those in the
instructions.
Caut ion
Handle the bracket 1 carefully to avoid injuring
your fingers.
Caut ions
• This unit is designed for negative ground 12 V
DC operation only.
• Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
• Before making connections, turn the car
ignition off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all ground w ires to a common ground
point.
• Be sure to insulate any loose unconnected
wires with electrical tape for safety.
•The use of optical instruments with this
product will increase eye hazard.
Notes on the pow er supply cord (yellow )
• When connecting this unit in combination with
other stereo components, the connected car
circuit's rating must be higher than the sum of
each component's fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Connect ion exam ple (2)
Notes ( 2 -B)
• Be sure t o connect t he ground cord bef ore
connect ing t he amplif ier.
• If you connect an opt ional pow er amplif ier and do
not use t he built -in amplif ier, t he beep sound w ill
be deact ivat ed.
Connect ion diagram (3)
1
To a metal surface of the car
First connect t he black ground lead, t hen
connect t he yellow and red pow er input
leads.
2
To the pow er antenna control lead or pow er
supply lead of antenna booster amplifier
Notes
• It is not necessary t o connect t his lead if
t here is no pow er ant enna or ant enna
boost er, or w it h a manually-operat ed
t elescopic ant enna.
• When your car has a built -in FM /AM
ant enna in t he rear/side glass, see " Not es
on t he cont rol and pow er supply leads."
3
To AM P REM OTE IN of an optional pow er
amplifier
This connect ion is only f or amplif iers.
Connect ing any ot her syst em may damage
t he unit .
4
To the +12 V pow er terminal w hich is
energized in the accessory position of the
ignition key sw itch
Notes
• If t here is no accessory posit ion, connect t o
t he +12 V pow er (bat t ery) t erminal w hich is
energised at all t imes.
Be sure t o connect t he black ground t o it
f irst .
• When your car has a built -in FM /AM
ant enna in t he rear/side glass, see " Not es
on t he cont rol and pow er supply leads."
5
To the +12 V pow er terminal w hich is
energised at all times
Be sure t o connect t he black ground t o it
f irst .
Notes on the control and pow er supply leads
• The pow er ant enna cont rol lead (blue) supplies
+12 V DC w hen you t urn on t he t uner.
• When your car has built -in FM /AM ant enna in
t he rear/side glass, connect t he pow er ant enna
cont rol lead (blue) or t he accessory pow er
input lead (red) t o t he pow er t erminal of t he
exist ing ant enna boost er. For det ails, consult
your dealer.
• A pow er ant enna w it hout relay box cannot be
used w it h t his unit .