Moulinex hv4 Mode D'emploi page 60

BEFORE USING FOR THE FIRST TIME
Wash all of the accessories and dry them carefully immediately.
USING YOUR APPLIANCE
M M I I N N C C I I N N G G H H E E A A D D ( ( A A ) ) : :
A A s s s s e e m m b b l l i i n n g g t t h h e e m m i i n n c c i i n n g g h h e e a a d d
( ( d d i i a a g g r r a a m m 1 1 ) )
Take the body ( ( A A 1 1 ) ) by the feeder tube,
placing the widest opening facing upwards.
Then introduce the screw A A 2 2 (long axis first)
into the body A A 1 1 ; ;
Fit the stainless steel blade A A 3 3 onto the short
axis that protrudes from the screw A A 2 2 , placing
the sharp edges towards the outside. Place
the disc of your choice onto the blade A A 3 3 ,
lining up the 2 lugs with the 2 notches on the
body A A 1 1 . .
Screw home (without locking) the nut A A 5 5 .
F F i i t t t t i i n n g g t t h h e e m m i i n n c c i i n n g g h h e e a a d d t t o o t t h h e e
a a p p p p l l i i a a n n c c e e ( ( d d i i a a g g r r a a m m 2 2 ) ) : :
Place the mincing head, with the feeder tube
angled to the right, opposite the unplugged
motor unit F F , ,
Line up the 2 bayonets of the mincing head
with the 2 notches on the motor unit.
Engage the mincing head fully into the motor
unit F F and then turn the feeder tube to the
left until it reaches a stop (the feeder tube
should be vertical at this point).
Engage the removable tray B B onto the lugs of
the mincing head feeder tube.
Plug in your appliance; it is ready for use.
U U s s e e : :
Prepare all of the food to be chopped and
remove the bones, cartilage and gristle. Cut
the meat into pieces (2 cm x 2 cm
approximately). Thaw frozen food thoroughly
before mincing. Place a container under the
mincing head. Press position 1 of button E E to
operate the appliance, place the pieces onto
the tray and slide them one by one into the
feeder tube using the pusher C C .
Never push food into the feeder tube with
your fingers or another utensil.
Do not use your appliance for more than
14 minutes at a time.
When you wish to chop very finely (with disc
A A 4 4 a a ) ) , it is imperative that you have
prechopped the meat beforehand using disc
A A 4 4 c c . If you do not follow this rule, you risk
damaging your appliance.
T T i i p p : :
A A t t t t h h e e e e n n d d o o f f t t h h e e o o p p e e r r a a t t i i o o n n , , y y o o u u c c a a n n p p a a s s s s a a
f f e e w w p p i i e e c c e e s s o o f f b b r r e e a a d d t t h h r r o o u u g g h h i i n n o o r r d d e e r r t t o o
r r e e m m o o v v e e a a l l l l o o f f t t h h e e m m i i n n c c e e . .
R R e e c c i i p p e e : :
N N B B : For recipes that require a high power
(500W approximately), the user time should
not exceed 20 seconds.
E E x x a a m m p p l l e e r r e e c c i i p p e e ( ( w w i i t t h h 4 4 . . 7 7 m m m m f f i i n n e e m m i i n n c c i i n n g g
d d i i s s c c A A 4 4 b b ) ) : :
L L a a m m b b o o r r M M u u t t t t o o n n w w i i t t h h s s p p l l i i t t p p e e a a s s : 150 g lamb
(shoulder or leg) or mutton, 45 g split peas
(soaked overnight and boiled for at least
10 minutes – see packet for instructions) ,
30 g plain flour, 15 ml cold water, 1 medium
onion, 2 cloves of garlic, salt and pepper.
Mix the split peas and the flour in a container
and then gradually add the water until you
obtain an even mixture. Place the pusher C C
into the feeder tube and start the appliance.
Gradually pour the mixture onto the tray,
while gently guiding the preparation into the
feeder tube with the pusher.
Chop the onion, garlic and meat into small 2
cm pieces and incorporate them into the mix.
Place 800 ml of water or vegetable stock into
a saucepan, season with salt and pepper
and add the preparation.
Simmer over a gentle heat for 1 hour, skim
and cover.
54