Publicité
Les langues disponibles
Les langues disponibles
Tools and Parts
IMPORTANT:
Installer: Leave these installation instructions with the
ƒ
homeowner.
Homeowner: Keep these installation instructions for future
ƒ
reference. Save them for the local electrical inspector's use.
Tools needed:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Cordless drill
ƒ
Drill bits
ƒ
Two adjustable wrenches
ƒ
Phillips screwdriver
ƒ
Small level
ƒ
Appliance dolly
ƒ
®†
Torx
T27 screwdrivers
ƒ
®
† Torx
is a registered trademark of Saturn Fasteners Inc.
Parts Needed:
Six #8 x 3" (7.6 cm) wood screws (longer screws may be
ƒ
needed)
One or two 2" x 4" x 32" (5.1 cm x 10.2 cm x 81.3 cm) wood
ƒ
board(s)
If you are connecting the water line directly to copper tubing
ƒ
and not to a shutoff valve, you need a ferrule, a union, and a
1/4" (6.4 mm) compression fitting.
Consult a qualified cabinetmaker or carpenter to make the
ƒ
custom panels. See page 9 for more information.
Location Requirements
Your Dacor refrigerator can be recessed in an opening between
cabinets or installed at the end of a cabinet run using a side panel
to enclose the refrigerator.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
IMPORTANT:
Observe all governing codes and ordinances.
ƒ
It is recommended that you do not install the refrigerator near
ƒ
an oven, radiator, or other heat source.
2
Installation Requirements
¹¹⁄
" nut driver
ƒ
32
³⁄
" and ¹⁄
" open-end wrenches
ƒ
8
2
Hex key (
5
⁄
")
ƒ
32
¹⁄
" and
5
/
" socket drivers
ƒ
4
16
Tape measure
ƒ
Utility knife
ƒ
Do not install in a location where the temperature will fall
ƒ
below 55°F (13°C).
The floor must support the refrigerator weight, more than 600
ƒ
lbs (272 kg), door panels and contents of the refrigerator.
The ceiling height must allow for side tipping radius. See
ƒ
Tipping Radius.
The location should permit doors to open fully. See Door
ƒ
Swing Dimensions.
The location must permit top grille removal. See Opening
ƒ
Dimensions.
Opening Dimensions
To avoid tipping during use, the solid soffit must be within 1"
ƒ
(2.5 cm) maximum above the refrigerator. If the solid soffit
is higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
If anti-tip boards are needed, they must be installed to the
rear wall studs so that the bottom of the anti-tip board is 84"
(213.4 cm) from the floor. See Install Anti-Tip Boards for more
information.
NOTES:
- A clearance of ¹⁄
" (1.3 cm) must be maintained above the
2
top grille in order for the top grille to be removed.
- Do not remove the foam gasket on top of the compressor
cover unless removal is necessary to fit the unit under
a soffit. Removal of the gasket will cause loss in cooling
efficiency.
- If installing under a solid soffit, after installation raise the
leveling legs so that the gasket is pressed snugly against
the soffit.
A
B
A. Gasket
B. Compressor cover
¹⁄
" (1.3 cm)
2
Publicité
