Grohe Seabury 25 502 Instructions D'installation page 5

Application
Operation is possible in conjunction with:
- Pressurized storage heaters
- Thermally controlled instantaneous heaters
- Hydraulically controlled instantaneous heaters
Operation with low-pressure storage heaters
(displacement water heaters) is not possible.
Technical data
• Max. flow
- Spout
- Handshower
• Flow pressure
- min.
- recommended
- greater than 72.5 psi, fit with pressure reducing valves
• Max. operating pressure
• Test pressure
• Temperature
- max. (hot water inlet)
• Water connection
Notes
- Installation of backflow protection must comply with local
codes and regulations.
- An access panel must be provided for access to diverting
unit and hose connections.
- Major pressure differences between cold and hot water
supply should be avoided.
Installation
Layout dimensions to establish proper clearances, see
dimensional drawing on page 1.
Flush pipes thoroughly!
Side valves
• Valve marked with "L" (left close) on the top edge of the
headpart (A) with blue tape should be mounted on the right
(cold water) side, see fig. [1].
• Valve marked with "R" (right close) on the top edge of the
headpart (A) with red tape should be mounted on the left
(hot water) side.
1. Screw the mounting set (B) to the bottom of the thread of the
side valve (C), see fig. [1].
Make sure that the rubber washer (B1) is on the top of the
fiber washer (B2).
2. Insert the side valve (C) through the basin hole from below.
3. Place the escutcheon O-ring (D1) on the basin and screw
down the escutcheon (D) until it stops.
4. Screw the cap (E) down to the escutcheon (D).
5. Cross handle (F):
- Secure the handle (F) to the stem of the headpart (A).
Lever handle (G):
- Close the headparts (clockwise for the hot side and
counter-clockwise for the cold side).
- Install the lever handle to the stem of the headpart and be
sure that the lever points away from the spout.
- Screw the brass nut (G1) into the cap (E) until tight.
- Screw the ring (G2) to cover the brass nut (G1).
6. Tighten the mounting set (B) from below to secure the valve.
approx. 50 L/min or 13.2 gpm
max. 9.5 L/min or 2.5 gpm
7.25 psi
14.5 - 72.5 psi
145 psi
232 psi
176 °F
cold - Right hand
hot - Left hand
English
Spout, see fig. [2].
1. Place the O-ring (I1) and the escutcheon (H1) on the basin.
2. Insert the spout (H) through the escutcheon (H1) and basin.
3. Secure the spout with the mounting set (I).
4. Install the diverter (J) to the spout, gently guiding the lift rod
assembly (K) up through the center of the spout (H).
5. Tighten the lift rod knob (L) to lift rod assembly (K).
Handshower, see fig. [3].
1. Install the escutcheon (M1) onto the guide (M).
2. Install the guide (M) through the mounting surface, insure
the escutcheon O-ring (N1) is in place.
3. Secure with mounting set (N).
4. Insert shower hose (O) through guide (M) from below.
5. Tighten the shower hose (O) to the handshower (P).
Connect faucet, see figs. [4] and [5].
Install elbows (Q) onto the diverter (J).
Connect the side valves to the water supply. Insure the
supplied washers are used for all connections.
The cold water supply should be connected on the right side
valve (marked blue) and the hot water supply to the left valve
(marked red).
The shower hose must be connected to the diverter.
Open cold and hot water supply and check connections
for leakage.
Maintenance
Inspect and clean all parts, replace as necessary and grease
with special grease (order no. 18 012).
Shut off cold and hot water supply.
I. Ceramic headpart, see page 2.
1. Remove handle (45 767, 45 768) and cap.
2. Unscrew the ceramic headpart (45 882 - right close,
45 883 - left close) using a 17mm wrench.
II. Flow straightener, see page 2.
Unscrew and clean flow straightener (13 933).
III. Shower, see page 2 and fig. [6].
1. Replace shower rose kit (45 792), see page 2.
2. Guaranteed for 5 years, the "SpeedClean" jets can be
freed of limescale simply by wiping across them firmly
with the palm of your hand, see fig. [6].
IV. Check valve
1. Disconnect shower hose (28 158), see see page 2.
2. Remove check valve (08 565).
Assemble in reverse order.
Replacement parts, see see page 2 ( * = special
accessories).
Care
Instructions for care of this faucet will be found in the Limited
Warranty supplement.
4