Wolfcraft TC 610 W Traduction De La Notice D'utilisation Originale page 12

t
WORKING INSTRUCTIONS
Parallel cuts (90°)
Push the cutting unit to the rear stop using the handle. Always make sure the cutting edge moves freely above the support plate. Then loosen
the two knurled screws and pull out the parallel stop to its maximum extended length of 300 mm (Fig. 2.1).
Place the tile in the unit so it is in contact with the front stop. You can set cutting widths from 50 – 300 mm (example = 200 mm) using the
parallel stop, or you can mark the cutting width on the tile with a suitable pen.
Then tighten the knurled screws of the parallel stop (Fig. 2.2).
Scoring the tile surface: Position the cutting wheel on the tile and, using the handle, push the cutting unit all the way to the front stop while
exerting pressure on the tile (Fig. 2.3). Swivel the handle up as far as it will go in the direction of the arrow. This automatically lifts the cutting
edge above the tile (Fig. 2.4).
Breaking the tile: Push the tile parallel to the support plate until the tile and breaking point completely overlap. Caution: The breaking point
must be precisely centred below the slot scored in the tile (Fig. 2.5). Using the handle, push the cutting unit towards the rear stop until the
cutting edge is exactly above the breaking point. Then press the handle down to break the tile (Fig. 2.6). The tile breaks along the scored line.
Using the handle, push the cutting unit to the front stop and remove the tile (Fig. 2.7).
Diagonal cuts (45°), square tiles
Using the handle, push the cutting unit to the rear stop and remove the parallel stop as shown (Fig. 3.1). Align the tile so that its corner is in
the V-groove of the stop block in the unit (Fig. 3.2).
Scoring the tile surface: Position the cutting wheel on the tile and, using the handle, push the cutting unit all the way to the front stop while
exerting pressure on the tile (Fig. 3.3). Swivel the handle up as far as it will go in the direction of the arrow. This automatically lifts the cutting
edge above the tile (Fig. 3.4).
Breaking the tile: Push the tile parallel to the support plate until the tile and breaking point completely overlap. Caution: The breaking point
must be precisely centred below the slot scored in the tile (Fig. 3.5). Using the handle, push the
cutting unit towards the rear stop until the cutting edge is exactly above the breaking point. Then press the handle down to break the tile (Fig.
3.6). The tile breaks along the scored line. Using the handle, push the cutting unit to the front stop and remove the tile (Fig. 2.7).
Transport
For transporting, push the cutting unit fully to the end of the device as shown. Then dismantle the parallel stop as shown and carry the tile
cutter by the handle with one hand (Fig. 4).
MAINTENANCE/SERVICE
• Inspect the tile cutter each time before using it.
• Remove dust and residues from the guide rails each time after using the tile cutter.
• Wipe off contaminants with a wet, soft cloth. Do not use any cleaning agents or solvents.
• Lubricate the guide rails of the TC 610 W regularly, basically each time before using it.
• Keep the safety and all other instructions for future reference in a safe place.
ENVIRONMENTAL PROTECTION
Do observe all applicable local disposal regulations, when disposing of the tile cutter TC 610 W.
Warranty
Dear hobbyist!
You have purchased a high-quality wolfcraft ® appliance, which we know you will enjoy using. wolfcraft ® appliances are built to high technical
standards, and undergo intensive development and test phases before leaving the factory. Constant controls and regular tests during
their manufacture, ensure a high quality standard. Sound technical developments, and reliable quality controls warrant for the right choice
of appliance.
We provide a warranty of 10 years from the day of purchase on the wolfcraft ® product you acquired, provided it is exclusively used for DIY
purposes. The warranty only covers damage to the item purchased, and only such damage that can be attributed to faulty material und poor
workmanship. The warranty does not cover defects and damage that must be attributed to improper use or insufficient maintenance.
Nor does the warranty cover the usual wear and tear as well as defects and damage, of which the customer has been aware when purchasing
the equipment.
Warranty claims can only be asserted by producing the invoice or the till receipt.
The warranty granted by wolfcraft ® does not in any way restrict your statutory consumer rights (i.e. contract performance, withdrawal from
the contract, price reduction, claims for damages or reimbursement of expenses).
12