Publicité
MAIN SCREEN
HOT WATER MAINTENANCE
NOW
Contains 3 areas:
SYSTEM
1. Actual Maintain temperature (red area)
INFO, RESET, SERVICE, TEST....
2. Next event temperature (grey area)
HEATING CABLE & PIPE
CABLE TYPE, PIPE DAIMETER,...
3. Hot water storage temperature
HOT WATER MAINTENANCE
GENERAL SETTINGS
(white area- if boiler sensor is connected and active)
COUNTRY, LANGUAGES, UNITS,...
Additional icons for settings, relay (ON/OFF), key lock or warning will be
WATER TEMP. & PROGRAM
HOT WATER MAINTENANCE
NOW
APPARTMENT, MAINTAIN, ECONOMY,....
displayed.When Lock is "on" a password is needed to access the parameter
menus. After the correct 4 number password is entered, each parameter in the
setup can be changed. The unit locks again after a 10 min. time out (no keys
NOW
pressed).
INFO
SETTINGS
TEST PROGRAM
RESET
SYSTEM
INFO, RESET, SERVICE, TEST....
SERVICE
HEATING CABLE & PIPE
SYSTEM
CABLE TYPE, PIPE DAIMETER,...
STATUS
INFO, RESET, SERVICE, TEST....
GENERAL SETTINGS
COUNTRY, LANGUAGES, UNITS,...
HEATING CABLE & PIPE
CABLE TYPE, PIPE DAIMETER,...
WATER TEMP. & PROGRAM
GENERAL SETTINGS
APPARTMENT, MAINTAIN, ECONOMY,....
HEATING CABLE & PIPE
COUNTRY, LANGUAGES, UNITS,...
WATER TEMP. & PROGRAM
SYSTEM
APPARTMENT, MAINTAIN, ECONOMY,....
SELECT CABLE TYPE
INFO
SELECT PIPE DIAMETER
TEST PROGRAM
SELECT INSULATION THICKNESS
INFO
RESET
SELECT AMBIENT TEMPERATURE
TEST PROGRAM
SERVICE
RESET
SELECT BOILER SENSOR
STATUS
SERVICE
SELECT BOILER CUT-OFF TEMPS.
STATUS
HEATING CABLE & PIPE
SELECT CABLE TYPE
Info
SELECT PIPE DIAMETER
SELECT CABLE TYPE
Test
SELECT INSULATION THICKNESS
SELECT PIPE DIAMETER
Programme
SELECT AMBIENT TEMPERATURE
SELECT INSULATION THICKNESS
SELECT BOILER SENSOR
SELECT AMBIENT TEMPERATURE
Reset
SELECT BOILER CUT-OFF TEMPS.
SELECT BOILER SENSOR
Service
SELECT BOILER CUT-OFF TEMPS.
NEXT
ECONOMY TEMP
SETTING
NEXT
ECONOMY TEMP
AT 17:00
SYSTEM
SETTING
SETTING
SYSTEM
HWAT-M
DN 25
SYSTEM
40 MM
20°C
ON
35/85°C
General info about the unit, name, commissioning date,
HWAT-M
HEATING CABLE & PIPE
firmware version, nVent contact info per country.
DN 25
The test programme runs for 30 minutes, during which
all parameters will be ignored to check the heating
40 MM
cable and the connection on site. You can stop the test
20°C
programme at any time.
Select "Yes" to activate the Quick install menu and return
ON
all settings to factory settings.
35/85°C
Quick start process restarts automatically.
Access for nVent SERVICE TEAM
14 : 14
AT 17:00
BOILER
14 : 17
14 : 14
14 : 14
NEXT
14 : 17
BOILER
ECONOMY TEMP
AT 17:00
BOILER
14 : 17
14 : 17
14 : 17
14 : 17
14 : 17
14 : 17
14 : 17
HWAT-M
DN 25
40 MM
20°C
ON
35/85°C
nVent.com/RAYCHEM
SELECT LANGUAGE
grey area
SELECT COUNTRY
SELECT DATE
white area
SELECT TIME
SELECT ALARM
red area
SELECT SAVING TIME
SELECT WATER TEMPERATURE
SELECT LANGUAGE
SELECT PROGRAM
SELECT COUNTRY
PROGRAM TIMER
SELECT LANGUAGE
SELECT DATE
SELECT COUNTRY
SELECT TIME
SELECT DATE
SELECT ALARM
SELECT TIME
SELECT SAVING TIME
SELECT ALARM
SELECT SAVING TIME
SELECT WATER TEMPERATURE
SELECT PROGRAM
SELECT WATER TEMPERATURE
PROGRAM TIMER
SELECT PROGRAM
PROGRAM TIMER
|
13
EN
G
DE
DK
CZ
FR
IT
NL
PL
ZH
W
GENERAL
WATER T
Publicité
