Télécharger Imprimer la page

Bosch GWS Professional 8-100 Z Notice Originale page 12

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 14
All manuals and user guides at all-guides.com
OBJ_BUCH-1556-004.book Page 12 Monday, February 8, 2016 8:05 AM
12 | English
Flap Disc
With the flap disc (accessory), curved surfaces and profiles
can be worked.
Flap discs have a considerably higher service life, lower noise
levels and lower sanding temperatures than conventional
sanding sheets.
Cutting Metal
 For cutting with bonded abrasives, always use the pro-
tection guard for cutting 13.
When cutting, work with moderate feed, adapted to the mate-
rial being cut. Do not exert pressure onto the cutting disc, tilt
or oscillate the machine.
Do not reduce the speed of running down cutting discs by ap-
plying sideward pressure.
The machine must al-
ways work in an up-
grinding motion. Other-
wise, the danger exists
of it being pushed un-
controlled out of the
cut.
When cutting profiles and square bar, it is best to start at the
smallest cross section.
Cutting Stone
 Provide for sufficient dust extraction when cutting
stone.
 Wear a dust respirator.
 The machine may be used only for dry cutting/grinding.
For cutting stone, it is best to use a diamond cutting disc.
When using the cutting guide with dust extraction protection
guard 20, the vacuum cleaner must be approved for vacuum-
ing masonry dust. Suitable vacuum cleaners are available
from Bosch.
Switch on the machine
and place the front part
of the cutting guide on
the workpiece. Slide the
machine with moderate
feed, adapted to the ma-
terial to be worked.
For cutting especially
hard material, e. g., con-
crete with high pebble
content, the diamond
cutting disc can over-
heat and become dam-
aged as a result. This is
clearly indicated by circular sparking, rotating with the dia-
mond cutting disc.
1 609 92A 28E | (8.2.16)
In this case, interrupt the cutting process and allow the dia-
mond cutting disc to cool by running the machine for a short
time at maximum speed with no load.
Noticeably decreasing work progress and circular sparking
are indications of a diamond cutting disc that has become
dull. Briefly cutting into abrasive material (e. g. lime-sand
brick) can resharpen the disc again.
Information on Structures
Slots in structural walls are subject to the Standard DIN 1053
Part 1, or country-specific regulations.
These regulations are to be observed under all circumstanc-
es. Before beginning work, consult the responsible structural
engineer, architect or the construction supervisor.
Maintenance and Service
Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
 In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a portable residual current device (PRCD).
When working metals, conductive dust can settle in the in-
terior of the power tool. The total insulation of the power
tool can be impaired.
Please store and handle the accessory(-ies) carefully.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
People's Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 4008268484
Fax: (0571) 87774502
E-Mail: contact.ptcn@cn.bosch.com
www.bosch-pt.com.cn
Bosch Power Tools

Publicité

loading

Ce manuel est également adapté pour:

Gws professional 8-115 z