Metabo 602265500 Notice Originale page 13

downwards so that the clamping nut can be
attached securely to the spindle.
B) In the case of thin (3 mm) accessories:
The collar of the clamping nut (6) faces upwards
so that the thin accessory can be clamped
securely.
- Lock the spindle (9) using the Allen key (10).
Tighten the clamping nut (6) by turning it
clockwise using the 2-hole spanner (11) (see
illustration c, page 2).
Releasing the clamping nut:
- Lock the spindle using the Allen key (10). Remove
the clamping nut (6) by turning it anticlockwise
using the 2-hole spanner (11) (see illustration b,
page 2).
8. Use
8.1 Setting speed
The speed can be preset via the setting wheel (5)
and is infinitely variable.
Positions 1-6 correspond approximately to the
following no-load speeds:
1......... 900 / min
2......... 1700 / min
3......... 2350 / min
The VTC electronics make material-compatible
work possible and an almost constant speed, even
under load.
8.2 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
3
I
Switching on: Push the slide switch (3) forward.
For continuous activation, now tilt
downwards until it engages.
Switching off: Press the rear end of the slide
switch (3) and release.
8.3 Working instructions
Press down lightly on the machine and move over
and back across the surface.
4 ....... 2800 / min
5 ....... 3400 / min
6 ....... 3800 / min
0
9. Cleaning
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
10. Troubleshooting
10.1 Mains powered machines:
- Overload protection: There is a MAJOR
reduction in load speed. The motor temperature
is too high! Allow the machine to run at idle speed
until it has cooled down.
- Overload protection: There is a SLIGHT
reduction in load speed. The machine is
overloaded. Reduce the load before continuing to
work.
- Metabo S-automatic safety shutdown: The
machine was SWITCHED OFF automatically. If
the slew rate of the current is too high (for
example, if the machine suddenly seizes or
kickback occurs), the machine switches off.
Switch off the machine using the slide switch (3).
Switch it on again and continue to work as normal.
Try to prevent the machine from seizing. See
Section 4.2.
- Restart protection: The machine does not
start. The restart protection is active. If the mains
plug is inserted with the machine switched on, or if
the power supply is restored following an
interruption, the machine does not start up. Switch
the machine off and on again.
11. Accessories
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
12. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
ENGLISH en
13