Servicing And Cleaning; Disposal; Product; Rechargeable Batteries - TOOLCRAFT 820921 Mode D'emploi

• Only use suitable bore bits or drills for the cordless screwdriver.
• Ensure your safe standing position when working, use a suitable ladder for example.
• Principally, use the electric tools only if you are concentrated and sober. A non-concentrated way of working or working
under alcohol or drugs cannot only damage the workpiece or electric device but can also cause high risk of injury!
• Do not overload the electrical appliances. Only use the electric devices for such operations for which they are provided.
For example, the cordless screwdriver must not be used for gauging mortar. Do not apply any force onto the cordless
screwdriver when screwing or drilling. Apart from the risk to damage the cordless screwdriver/accumulator there
is also risk of injury.
• Never touch the rotating drill chuck, the rotating drill or drill bit. Risk of injury!
• The heating-up of the cordless screwdriver or the installed accumulator during operation is normal. The same applies
for charging the accumulator.
• Keep the electrical appliances in a clean condition and clean them at regular intervals. In this way you can enjoy a
correctly functioning tool for a long period of time.
• Keep the electrical appliance at a dry and clean location (no damp cellars or places like that). The location at which
you keep the device must be out of the reach of children. Children cannot estimate the risks which can arise through
handling electrical appliances.

9. Servicing and cleaning

None of the components inside this product is to be serviced by the user. Therefore never open it.
Servicing or repair and any associated opening of the product may only be carried out by a specialist or a
specialist workshop.
A thorough cleaning maintains the operability of the product so that you can enjoy it for a long period of time. A good craftsman
is careful with his tools!
Before starting cleaning works set the turn-over switch (4) into its central position to block the drive.
Before cleaning the appliance, the plug-in charging set is to be separated from the mains voltage, pull it out
of the mains socket.
Remove dust by means of a clean long-hair brush and a vacuum cleaner.
Further cleaning only requires a dry, clean and lint-free cloth which can be damped a little bit in slightly warm water for more
concentrated dirt. Normally, special cleaning agents are not necessary!
Ensure that liquids do not enter into the interior of the device, because they could damage the product.
Improper cleaning agents can cause a discolouration at the plastic surface.
Never use aggressive scouring cleaners, alcohol, gasoline, spirit or similar liquids for cleaning the device!
After cleaning, allow the product to dry completely before operating it again! This applies particularly for the
plug-in charging set!
25

10. Disposal

a) Product
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
The built-in battery must be disposed of by a specialist.
b) Rechargeable batteries
You as the end user are required by law (Battery Ordinance) to return all used rechargeable batteries. Disposing of them in the
household waste is prohibited.
Contaminated (rechargeable batteries are labelled with this symbol to indicate that disposal in the domestic waste is
forbidden. The designations for the heavy metals involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on
rechargeable batteries, e.g. below the trash icon on the left).
Used rechargeable batteries can be returned to collection points in your municipality, our stores or wherever
(rechargeable batteries are sold.
You thus fulfil your statutory obligations and contribute to the protection of the environment.

11. Troubleshooting

In purchasing the cordless screwdriver, you have acquired a product which has been designed to the state of the art and is
operationally reliable. However, problems and faults can occur. Therefore at this point we would like to explain to you how you
can rectify possible faults.
Observe all safety instructions contained in these operating instructions without fail!
Problem Possible solutions
Device not functioning • Is the accumulator empty?
On/off switch cannot be • Set the turn-over switch to the position left or right. In the central position it blocks
pressed the on/off switch!
When drilling a drill progress • Check the sense of rotation of the drill, switch the turn-over switch to the other
cannot be observed. position.
• Use another drill.
For unscrewing or tightening • Adjust the torque-setting ring in such a way that the required torque is available
a screw the cordless
screwdriver vibrates.
Only slow rotation of the drill • Is the accumulator weak?
chuck
Drill chuck rotates, the drill or • Check if the drill chuck is tightened. Turn the two rings of the drill chuck in such a
the bore bit does not rotate way that the tool (drill or bore bit) is fixed.
(tool slides through)
• The clamping range of the drill chuck is too small. Insert the tool deeper into the drill
chuck.
• The cordless screwdriver is only suited for drills of between 0.8 mm and approx.
9 mm.
Drill chuck loose • Fasten the drill chuck as described in chapter 7. f).
26