IKRA ILH 2800 Manuel D'utilisation page 21

WARNING: This device has a rotating
blade.
WARNING: The blades do not stop mov-
ing immediately when the device is shut
down.
• Before undertaking any repair or cleaning
work, shut down the shredder, remove the plug
from the outlet, and wait until the blade comes
to a complete stop.
• You do not have the right to remove or modify
electric or mechanical protection equipment.
• Only use the shredder during daylight or with
strong artificial light.
• Never place your hands in the feeding funnel
or the ejection opening.
• If the unit emits unusual sounds or vibrations,
turn off the motor and look for the cause. In
general, vibrations are a sign of problems.
• Ensure that the blade is firmly attached before
you use the shredder. The device can only be
operated with a properly installed blade.
• The shredder must be inspected carefully be-
fore use. Only use machines that are in proper
functioning order. If you discover any damage
on or problems with the device which could
pose a risk to the user, have the damage re-
paired before using the machine again.
• Worn out or damaged components must be re-
placed immediately for reasons of safety. Only
use original replacement parts. Using non-
original parts can lead to defective functioning
and injury.
• Only use the shredder in areas in which it is
protected from water. Do not expose the de-
vice to rain.
• Store the shredder in a dry and secure location
and out of the reach of children.
• Younger, disabled or frail individuals may not
use this device without supervision.
• Supervise children in the proximity of the de-
vice to ensure that they do not play with the
machine.
2.1 Preparation
• Do not allow children to work with this device.
• Do not use this device in the presence of by-
standers.
• Always wear ear and eye protection during op-
eration.
• Avoid wearing loose-fitting clothing and cloth-
ing with hanging straps and bands.
• Only use the machine with plenty of open
GB | Operating Instructions
• Do not use the machine on a paved surface
• Before using, check all screws, nuts bolts and
2.2 Operation
• Before activation, inspect the collection con-
• Do not place your face or body near the feed-
• Do not place hands, other body parts, or cloth-
• Always place both feet on the ground securely.
• Always keep clear of the ejection area during
• When adding material thoroughly ensure that
• If the a foreign object ends up in the cutting
• Do not let the shredded material pile up in the
• If the machine starts to clog, shut it down (un-
• Keep all protection and shielding equipment in
• Do not tinker with the motor controller settings.
GB-4
space (e.g. not next to a wall or other fixed ob-
jects) and on a solid, even surface.
or on gravel where ejected objects could case
injury.
other fastening equipment to ensure that they
are secure. Also check the protection and
shielding equipment. Replace damaged and
illegible stickers.
tainer to ensure that it is empty.
ing funnel.
ing into the feeding funnel or ejection opening.
Do not bend over the unit. When feeding the
machine never stand higher than the surface
on which the machine is located.
operation.
there are no pieces of metal, stones, bottles,
cans or other foreign objects.
mechanism or if the machine starts to produce
unusual noises or vibrations, shut down the
device, wait until the blade stops, unplug the
device from the mains, remove the sparkplug
cable and the sparkplug, and proceed as fol-
lows:
1. Check the damages.
2. Check for loose parts and tighten them.
3. Replace any damaged parts or repair with
replacement parts (with the same specifica-
tions).
ejection area. This could prevent proper ejec-
tion or cause this material to recoil through the
filling opening.
plug the device from the mains) before fixing
the clog. Keep the power unit free from waste
and other build-up to avoid damage and poten-
tial risk of fire. Remember that the blades con-
tinue to operate after the machine is shut down.
good condition.
The controller regulates the safe maximum