Publicité
Les langues disponibles
Les langues disponibles
n O perations after first power-on
When you turn on the power for the first time, the language
settings screen appears. Be sure to set the date and time.
1. Select a language, and then touch "Next".
2. Select the time zone, and then touch "Next".
3. Set the date and time, and then touch "Next".
The operation mode settings screen appears.
4. Configure the settings according to the screen.
YES:
• "Operation mode" is set to "Mode1".
"Mode1" is the recommended setting and conforms to
the "Normal Configuration" as defined in the EcoDesign
Regulation (2019/2021).
• "Power management" is set to "Power standby" and
"Power save mode" is set to on.
These settings can not be changed.
• "Wake On LAN" is set to off.
• If there is no signal for approx. 5 minutes, this monitor
automatically enters standby mode.
• Current consumption is reduced while the monitor is in
standby state. APPLICATION mode is also shut down.
Note, however, that the startup time from standby state
becomes longer.
NO:
• "Operation mode" is set to "Mode2".
• "Power management" is set to "Signal waiting mode"
and "Power save mode" is set to off.
These settings can be changed.
• Move to input signal waiting state in the nosignal state.
• Startup time from standby state is reduced. Note,
however, that more power will be consumed in standby
state. APPLICATION mode continues to run in standby
state.
Even after being set, you can change the "Operation
mode". (See OPERATION MANUAL.)
The home screen of APPLICATION mode appears.
Model
PN-LC862
Power requirement
AC 100 - 240 V, 5.6 A,
50/60 Hz
Operating temperature *
41°F to 95°F (5°C to 35°C)
1
Operating humidity
20% to 80% (no condensation)
Power consumption *
2
260 W (500 W)
(Max)
Dimensions
inch (mm)
Approx. 77-1/2 (W) x 3-7/16 (D)
(excluding protrusions)
x 46-1/16 (H) (1967.9 x 87.1 x
1170.2)
Weight
lbs. (kg) Approx. 143.3 (65)
*1 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such cases,
please check the temperature condition specified by the optional equipments.
*2 Factory setting. (When no optional part is attached.)
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
Turning power off
1. Press the POWER button on the remote control unit.
Or, press and hold the POWER button on the monitor.
A confirmation screen appears.
2. Select "Power off".
The power will turn off. (Standby state)
Caution
• When the power is turned off, the application data that is
not saved is lost.
• A message is displayed before the power turns off. Save
any data you need.
• If the monitor will be turned off by schedule, "Off if no
operation" or computer control, save any data you need in
advance. The power will turn off even if there is unsaved
data. (The data will be lost.)
Specifications
PN-LC752
AC 100 - 240 V, 4.7 A,
50/60 Hz
200 W (420 W)
Approx. 67-13/16 (W) x 3-7/16
(D) x 40-5/8 (H) (1722.5 × 87.1
× 1032.1)
Approx. 112.4 (51)
POWER button
PN-LC652
AC 100 - 240 V, 4.4 A,
50/60 Hz
180 W (390 W)
Approx. 59-1/2 (W) x 3-3/8 (D)
x 36-1/8 (H) (1511.6 × 85.9 ×
917.9)
Approx. 84.9 (38.5)
9
E
Publicité
