Makita LS1017 Manuel D'instructions page 14

After adjusting the kerf boards, release the stopper pin
and raise the handle. Then tighten all the screws securely.
NOTICE:
• After setting the bevel angle ensure that the kerf
boards are adjusted properly. Correct adjustment of
the kerf boards will help provide proper support of the
workpiece minimizing workpiece tear out.
Maintaining maximum cutting capacity
This tool is factory adjusted to provide the maximum
cutting capacity for a 255 mm saw blade.
Unplug the tool before any adjustment is attempted.
When installing a new blade, always check the lower limit
position of the blade and if necessary, adjust it as follows:
(Fig. 7 & 8)
First, unplug the tool. Push the carriage toward the guide
fence fully and lower the handle completely. Use the hex.
wrench to turn the adjusting bolt until the periphery of the
blade extends slightly below the top surface of the turn
base at the point where the front face of the guide fence
meets the top surface of the turn base.
With the tool unplugged, rotate the blade by hand while
holding the handle all the way down to be sure that the
blade does not contact any part of the lower base. Re-
adjust slightly, if necessary.
WARNING:
• After installing a new blade and with the tool
unplugged, always be sure that the blade does not
contact any part of the lower base when the handle
is lowered completely. If a blade makes contact with
the base it may cause kickback and result in serious
personal injury.
Stopper arm (Fig. 9)
The lower limit position of the blade can be easily
adjusted with the stopper arm. To adjust it, move the
stopper arm in the direction of the arrow as shown in the
figure. Adjust the adjusting screw so that the blade stops
at the desired position when lowering the handle fully.
Adjusting the miter angle (Fig. 10)
Loosen the grip by turning counterclockwise. Turn the turn
base while pressing down the lock lever. When you have
moved the grip to the position where the pointer points to
the desired angle on the miter scale, securely tighten the
grip clockwise.
CAUTION:
• After changing the miter angle, always secure the turn
base by tightening the grip firmly.
NOTICE:
• When turning the turn base, be sure to raise the handle
fully.
Adjusting the bevel angle (Fig. 11)
To adjust the bevel angle, loosen the lever at the rear of
the tool counterclockwise. Unlock the arm by pushing the
handle somewhat strongly in the direction that you intend
to tilt the saw blade.
14
All manuals and user guides at all-guides.com
NOTE:
• Lever can be adjusted to a different lever angle by
Tilt the saw blade until the pointer points to the desired
angle on the bevel scale. Then tighten the lever clockwise
firmly to secure the arm. (Fig. 13)
When tilting the carriage to the right, tilt the carriage to the
left slightly after loosening the lever and press the
releasing button. With the releasing button being pressed,
tilt the carriage to the right. (Fig. 14)
Tilt the saw blade until the pointer points to the desired
angle on the bevel scale. Then tighten the lever clockwise
firmly to secure the arm.
• When changing bevel angles, be sure to position the
• After changing the bevel angle, always secure the arm
NOTICE:
• When tilting the saw blade be sure the handle is fully
• When changing bevel angles, be sure to position the
Slide lock adjustment (Fig. 15)
To lock the slide pole, turn the locking screw clockwise.
Switch action
For European countries (Fig. 16)
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool, push
the lever to the left, press in the lock-off button and then
pull the switch trigger. Release the switch trigger to stop.
• Before plugging in the tool, always check to see
A hole is provided in the switch trigger for insertion of
padlock to lock the tool off.
For all countries other than European countries
(Fig. 17)
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
• Before plugging in the tool, always check to see
removing the screw holding the lever and securing the
lever at a desired angle. (Fig. 12)
kerf boards appropriately as explained in the
"Positioning kerf boards" section.
CAUTION:
by tightening the lever clockwise.
raised.
kerf boards appropriately as explained in the
"Positioning kerf boards" section.
WARNING:
that the switch trigger actuates properly and
returns to the "OFF" position when released. Do
not pull the switch trigger hard without pressing in
the lock-off button. This can cause switch
breakage. Operating a tool with a switch that does not
actuate properly can lead to loss of control and serious
personal injury.
WARNING:
that the switch trigger actuates properly and
returns to the "OFF" position when released. Do
not pull the switch trigger hard without pressing in
the lock-off button. This can cause switch
breakage. Operating a tool with a switch that does not