IVT GBC-43 Mode D'emploi page 11

two hands when operating unit.
∙ The device has normally to be used at ground level
with the cutting attachment parallel to the ground. Do
not use the device to cut grass that is not on the ground
level, e.g. grass that grows on walls, rocks etc.
∙
Before cutting, inspect the area for stones, glass,
pieces of metal, trash or other solid objects. Make sure
that the cutting equipment does not come in contact
with stones, gravel, wire or other foreign bodies during
the start-up and while working. The cutting attachment
could throw object of this kind.
∙ Always keep a safety distance of 15 m around
yourself. Stones and gravel can be thrown off, which
can cause injuries.
∙ Within the range of action, the user is responsible
for damages to third parties which have been caused by
the use of the device.
∙ Stop using the machine while people, especially
children, or pets are nearby.
∙ Never operate the unit with damaged safety guards
or without the safety guard in place. Make sure the
appropriate safety guard is in place.
∙ Before using the machine and after any impact,
check for signs of wear or damage and repair as
necessary.
∙
Keep the cutting tool, especially when rotating, at a
distance from all parts of your body, particularly hands
and feet.
∙
Always keep proper footing and balance at all
times. Be especially cautious while working on slopes,
on overgrown terrain or in slippery conditions. Watch out
for hidden obstacles.
∙ Take care against injury from the line cutter fitted for
trimming the cutting line length.
∙ Do not cross any gravel-strewn roadways or paths
with device still running.
∙
Do not operate unit for prolonged periods, rest
periodically. Limit the amount of time over which the
device is to be used continuesly (around 30-40 minutes
per session), and take 10-20 minutes of rest between
work sessions. Also try to keep the total amount of work
performed in a single day under 2 hours or less.
∙ Replace trimmer spool if cracked, chipped or
damaged in any way. Be sure it is properly installed and
securely fastened.
∙ Never use blades that are uncorrect, bent, warped,
cracked, broken or damaged. Keep the blade always
sharp. Check the bolt to fasten the blade and be sure
the blade turns freely without abnormal noise.
CAUTION! After stopping the engine,
the cutting equipment keeps on rotating
for some seconds. Never attempt to
stop it with your hands. Always wait
until it stops by itself completly.
∙ Operate the brushcutter only with the shoulder
strap (or backpack) attached. Check it is not damaged
before use. It should be properly adjusted to user's size
before putting the brushcutter into operation.
∙
Stop the engine during transport.
CAUSES AND OPERATOR PREVENTION
OF THE KICKBACK
When operating the brushcutter, uncontrolled kickback
can occur. Kickback is the sudden and uncontrolled
motion of the machine and cutting tools towards the
operator that can occur:
∙
if the blade binds in the cut;
∙ if the blade segment between 12 and 2 o'clock, as
viewed from the operator's position [F1] of a rotating
blade comes in contact with a solid rigid object like tree,
rock, bush or wall.
This kickback can cause loss of control of the unit and
may result in serious or fatal injury to the operator or
bystanders.
To avoid kickback and reduce the risk of loss of control:
∙
before beginning work, watch out for hidden
obstacles, such as rocks, stumps, roots, etc., that could
cause the blade to kick back if struck.
∙ always handle the device securely with two hands
and do not grip other parts except the handles.
∙
replace or resharpen dull blades.
∙ never raise the unit above your waist.
∙
avoid operating the brushcutter using the blade
segment between the 12 and 2 o'clock position.
UNPACKING
When unpacking, check to make sure that all
components are included. Refer to the drawings on this
manual. If any parts are missing or broken, please call
an IVT assistance center.
11
Instruction manual
EN