Double Insulation For Safer Operation - Metabo HPT G 18SE3 Instructions De Sécurité Et Mode D'emploi

guard or safety feature, be sure to replace the guard
or safety feature before resuming operation of the
tool.
8. Use right tool.
Don't force small tool or attachment to do the job of a
heavy-duty tool.
Don't use tool for purpose not intended —for
example— don't use circular saw for cutting tree
limbs or logs.
9. NEVER use a power tool for applications other
than those specifi ed.
NEVER use a power tool for applications other than
those specifi ed in the Instruction Manual.
10. Handle tool correctly.
Operate the tool according to the instructions provided
herein. Do not drop or throw the tool. NEVER allow the
tool to be operated by children, individuals unfamiliar
with its operation or unauthorized personnel.
11. Keep all screws, bolts and covers tightly in place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
12. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool's housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
13. Blades and accessories must be securely
mounted to the tool.
Prevent potential injuries to youself or others. Blades,
cutting implements and accessories which have been
mounted to the tool should be secure and tight.
14. Keep motor air vent clean.
The tool's motor air vent must be kept clean so that
air can freely fl ow at all times. Check for dust build-up
frequently.
15. Operate power tools at the rated voltage.
Operate the power tool at voltages specifi ed on its
nameplate.
If using the power tool at a higher voltage than the
rated voltage, it will result in abnormally fast motor
revolution and may damage the unit and the motor
may burn out.
16. NEVER use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually, making
strange noises, or otherwise appears defective, stop
using it immediately and arrange for repairs by a
metabo HPT authorized service center.
17. NEVER leave tool running unattended. Turn
power off .
Don't leave tool until it comes to a complete stop.
18. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
19. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened
with soapy water and dry thoroughly.
20. NEVER use a depressed center wheel which
is cracked or deformed or worn away (see the
MAINTENANCE AND INSPECTION section on
page 13).
21. NEVER use the grinder in places where the sparks
generated by the grinder can cause explosion, such
as where fl ammable materials or gases are present.
22. NEVER push in the push button while the spindle is
running.
23. ALWAYS wear eye protection that meets the
requirement of the latest revision of ANSI
Standard Z87.1.
24. ALWAYS wear a mask or respirator to protect yourself
from dust or potentially harmful particles generated
during the grinding operation.
25. ALWAYS fi rmly grip the body handle and side handle
while operating the grinder.
26. ALWAYS have a trial run before grinding commence.
(see Test the grinder before using on page 11).
27. ALWAYS follow the instructions contained in this
manual when replacing the depressed center wheel.
28. ALWAYS be careful with buried objict such as an
underground wiring.
Touching these active wiring or electric cable with this
tool, you may receive an electric shock.
Comfi rm if there are any buried object such as electric
cable within the wall, fl oor or ceiling where you are
going to operate here after.
29. Secure the workpiece and check that the workpiece
is properly supported. A workpiece clamped with
clamping devices or in a vice is held more securely
than by hand.
30. Defi nitions for symbols used on this tool
V ..............volts
Hz ............hertz
A ..............amperes
n ..............rated speed
W .............watt
...........Class II Construction
---/min ......revolutions per minute
DOUBLE INSULATION FOR SAFER
OPERATION
To ensure safer operation of this power tool, metabo HPT
has adopted a double insulation design. "Double insulation
" means that two physically separated insulation systems
have been used to insulate the electrically conductive
materials connected to the power supply from the outer
frame handled by the operator. Either the symbol "
the words "Double insulation" appear on the power tool or
on the nameplate.
English
" or
7