JVC TK-C676 Instructions page 35

AUTO PATROL Setup
Use the AUTO PATROL screen to set the configuration of the auto patrol function, which moves the camera between several positions
at a high speed.
Patrol positions 1-100 can be set in each of three modes (MODES 1 to 3). It is recommended that these three modes be set the
according to the day of the week or the time of day. For example: MODE 1 for nighttime and MODE 2 for daytime.
High
speed
P O S I
N
I T I O
P O S
1
High speed
P O S
I T I O
High
N
speed
4
MENU button
SET button
REMOTE CONTROL UNIT
CAMERA POSITION
SETUP POWER
ALARM
MENU SET AUTO F-1
KEY LOCK
LENS CAMERA/POSITION PAN/TILT
1 2 3
CAMERA POSI-
SPEED
TION
IRIS 4 5 6 OPTION OPTION
CLOSE OPEN
1 2
FOCUS
NEAR FAR 7 8 9 AUTO AUTO
AF
PAN PATROL
0
ZOOM TELE CLEAR ENTER
WIDE
/HOME
FAR button
WIDE button
NEAR button
– – – A U T O P A N / P A T R O L / T R A C E – – –
A U T O P A N M O D E R E T U R N
A U T O P A N S P E E D N O R M A L
A . P A N S T A R T P O S . S E T . .
A . P A N R E T U R N P O S . S E T . .
A U T O P A T R O L S E T . .
A U T O T R A C E S E T . .
R M A . P A N K E Y A . P A N
R M A . P A T R O L K E Y A . P A T R O L
AUTO PAN/PATROL/TRACE menu
A U T O P A T R O L MO D E 1
P A T R O L 1 H OM E 1 0 s
P A T R O L 2 P O S 1 1 0 s
P A T R O L 3 P O S 2 1 0 s
P A T R O L 4 P O S 3 1 0 s
P A T R O L 5 P O S 4 1 0 s
P A T R O L 6 P O S 5 1 0 s
P A T R O L 7 P O S 6 1 0 s
P A T R O L 8 P O S 7 1 0 s
F W D / B W D / Z O O M M O D E / F O C U S
AUTO PATROL MODE 1 screen
(Example showing PATROL Nos.1 to 8)
A U T O P A T R O L MO D E 1
P A T R O L 9 P O S 8 1 0 s
P A T R O L 1 0 P O S 9 1 0 s
P A T R O L 1 1 P O S 1 0 1 0 s
P A T R O L 1 2 P O S 1 1 1 0 s
P A T R O L 1 3 P O S 1 2 1 0 s
P A T R O L 1 4 P O S 1 3 1 0 s
P A T R O L 1 5 P O S 1 4 1 0 s
P A T R O L 1 6 P O S 1 5 1 0 s
F W D / B W D / Z O O M M O D E / F O C U S
AUTO PATROL MODE 1 screen
(Example showing PATROL Nos. 9 to 16)
All manuals and user guides at all-guides.com
1.
T I O N
2
2.
High speed
3.
RM-P2580
F-2 F-3
CAMERA
4.
buttons
PAN/TILT
lever
5.
ENTER
button
TELE button
6.
7.
8.
9.
10.
• After the above setup, auto patrol of the camera can be started by
• To change the auto patrol mode after the above setup, display the
• The auto patrol function can only be set from an RM-P2580. Note
Select the camera. ( RM-P2580 Instruction manual)
CAMERA button → Numeric key (camera number) → ENTER button.
The picture of the selected camera is output.
Display the SETUP menu on the camera.
1 4
( P. 18, steps to )
MENU button (3 sec.) → Select "CAMERA" with the PAN/TILT lever
→ SET button.
The camera moves to the home position.
Tilt the PAN/TILT lever up or down to move the cur-
sor (>) to "AUTO PAN/PATROL TRACE" and press
the SET button.
The AUTO PAN/PATROL/TRACE menu is displayed.
Move the cursor (>) to "AUTO PATROL SET" and
press the SET button.
The AUTO PATROL MODE 1 screen is displayed.
Tilt the PAN/TILT lever to move the cursor (>) to the
PATROL position to be set.
• To display the next page (PATROL positions 9 to 19), press the
TELE button.
• To display the previous page, press the WIDE button.
Set a patrolled position.
POSITION button → Numeric key (position number) → ENTER button.
• At the factory settings, positions PATROL 1 to 100 are set to HOME
to 99 in that order.
Even when positions between POS 64 and POS 99 are set, the auto
patrol operation skips them automatically and they are not switched.
Set the length of time a camera will stay in each
position.
• Tilt the PAN/TILT lever to the left or right to set the time period.
• Available setting values: SKIP, 5s, 10s, 20s, 30s, 45s, 1min, 2min.
(Selecting "SKIP" skips that position and moves to the next position.)
• The factory setting is "10s" for all positions.
5 7
Repeat steps to for each patrolled position.
• Set the patrolled positions and time periods of all patrol numbers
in this way.
Change the auto patrol mode.
• Press the FAR or NEAR buttons to change the mode.
• After changing to a new mode, repeat steps
Press the MENU button.
• The screen returns to the previous menu.
pressing the AUTO PATROL button on the RM-P2580.
AUTO PATROL MODE screen and press the FAR or NEAR but-
tons.
that it differs to auto sequence operations available with other re-
mote control units.
5 8
to .
E-35