JVC TK-C676 Instructions page 34

Setting Up the Camera Using an RM-P2580
AUTO PAN Setup
Use the AUTO PAN screen to set the auto pan function, which allows the camera to be revolved slowly in a horizontal direction)
The auto pan function has three modes, the RETURN mode for continual movement between two positions, the RIGHT mode for
clock-wise rotation and the LEFT mode for counterclockwise rotation.
Slow movement
MENU button
SET button
REMOTE CONTROL UNIT RM-P2580
CAMERA POSITION
SETUP
POWER
ALARM
MENU SET AUTO F-1 F-2
KEY LOCK
LENS CAMERA/POSITION PAN/TILT
1 2 3
SPEED CAMERA POSI-
TION
4 5 6
CLOSE IRIS OPEN OPTION OPTION
1 2
FOCUS
7 8 9
NEAR FAR AUTO AUTO
AF
PAN PATROL
0
WIDE ZOOM TELE CLEAR ENTER
/HOME
ENTER button
TELE button
FAR button
WIDE button
NEAR button
– – – A U T O P A N / P A T R O L / T R A C E – – –
A U T O P A N M O D E R E T U R N
A U T O P A N S P E E D N O R M A L
A . P A N S T A R T P O S . S E T . .
A . P A N R E T U R N P O S . S E T . .
A U T O P A T R O L S E T . .
A U T O T R A C E S E T . .
R M A . P A N K E Y A . P A N
R M A . P A T R O L K E Y A . P A T R O L
AUTO PAN/PATROL/TRACE menu
– – – S T A R T P O S I T I O N S E T – – –
P U S H M E N U / S A V E & R E T U R N /
START POSITION SET screen
– – – R E T U R N P O S I T I O N S E T – – –
/
P U S H M E N U S A V E & R E T U R
RETURN POSITION SET screen
E-34
All manuals and user guides at all-guides.com
1.
2.
3.
4.
F-3
CAMERA
buttons
PAN/TILT
lever
5.
6.
7.
8.
9.
MEMO
• It is not possible to tilt the camera or change the lens settings at
• If the SET or MENU buttons are pressed while the camera is mov-
10.
After the above setup, auto panning of the camera can be started by
N
pressing the AUTO PAN button on the RM-P2580.
Select the camera. ( RM-P2580 Instruction manual)
CAMERA button → Numeric key (camera number) → ENTER button.
The picture of the selected camera is output.
Display the SETUP menu on the camera.
1 4
( P. 18, steps to )
MENU button (3 sec.) → Select "CAMERA" with the PAN/TILT lever
→ SET button.
The camera moves to the home position.
Tilt the PAN/TILT lever up or down to move the cur-
sor (>) to "AUTO PAN/PATROL TRACE" and press
the SET button.
The AUTO PAN/PATROL/TRACE menu is displayed.
Set the auto pan mode and speed.
• Select the "AUTO PAN MODE" item and then select either RE-
TURN (continual movement between two positions),
RIGHT(clockwise rotation) or LEFT (counterclockwise rotation).
• Select the "AUTO PAN SPEED" item and then select either LOW,
NORMAL or HIGH.
Move the cursor (>) to "A. PAN START POSITION
SET" and press the SET button.
The START POSITION SET screen is displayed.
Adjust the viewing angle of the start position.
• Use the PAN/TILT lever, FOCUS button and ZOOM button to ad-
just the viewing angle.
• Tilting of the camera and changes in lens controls such as the
FOCUS and ZOOM settings are not available at the return posi-
tion.
Press the MENU button.
The AUTO PAN/PATROL/TRACE screen shows "DATA SAVED" to
indicate that the viewing angle for the start position has been regis-
tered.
Move the cursor (>) to "A. PAN RETURN POSITION
SET" and press the SET button. (RETURN mode only)
The RETURN POSITION SET screen is displayed.
Adjust the viewing angle of the return position.
(RETURN mode only)
Pan the camera in the right and left directions and adjust the view-
ing angle.
the return position.
ing, the correct settings cannot be registered. Make sure that the
camera is stationary before pressing the SET or MENU buttons.
Press the MENU button.
• The screen returns to the previous menu.
"Auto Panning" in the RM-P2580 Instruction manual.