SunPower PERFORMANCE P6-COM-S-BF Instructions D'installation page 12

Shading incidence need to be avoided during PV system operation.
The system is not supposed to be energized until the mounting
scaffolding, fences or railing have been removed from the roof.
Systems should be disconnected in any cases of maintenance which
can cause shading (e.g. chimney sweeping, any roof maintenance,
antenna/dish installations, etc).
6.0 Maintenance
Maxeon recommends visual inspection on a regular basis of all
modules for safe electrical connections, sound mechanical
connection, and free from corrosion. This visual inspection should be
performed by trained personnel. The standard frequency is once a
year according to environmental conditions, periodic cleaning of
modules is recommended but is not required. Periodic cleaning has
resulted in improved performance levels, especially in regions with
low levels of annual precipitation (less than 46,3cm (18,25 inches)).
Consult your dealer or supplier about recommended cleaning
schedules for your area.
Table 2: Module Frame Details
Platform
Residential
Modules
FOR COMMERCIAL (SILVER FRAME) MODULES ONLY, INCLUDES STACKING PINS
96 CELL COMMERCIAL MODULE
4X Ø 4.8 mm
Drain Holes
12X Ø 6.6 mm
Mounting Holes
6X Ø 4.2 mm
Commercial
Ground Holes
Modules
4X Ø 6.10 mm
Stackings Pins
398 mm
3.2 mm
Measurement Tolerances are +/‐3 mm for the Length and Width of the Module.
© December 2021 Maxeon Solar Technologies, Ltd. All rights reserved. Specifications included in this manual are subject to change without notice.
Module mounting and ground hole detail
RESIDENTIAL G3 FRAME ONLY
96 CELL MODULE FRAME DETAIL
(Front View)
(Back View)
Method 1:
Frame Hole
Locations
46 mm
Safety and Installation Instructions ‐ Document 001‐15497 Rev.W
To clean a module, wash with potable, non‐heated, water. Normal
water pressure is more than adequate, but pressurized water up to
100 bar (min.50 cm distance) may be used. Maxeon recommends
using a large hosepipe and not to perform cleaning at high outside
temperatures. Fingerprints, stains, or accumulations of dirt on the
front surface may be removed as follows: first rinse off area and let
soak for a short period of time (5 mins). Re‐wet and use a soft sponge
or seamless cloth to wipe glass surface in a circular motion.
Fingerprints typically can be removed with a soft cloth or sponge and
water after wetting. Do not use harsh cleaning materials such as
scouring powder, steel wool, scrapers, blades, or other sharp
instruments to clean the glass surface of the module. Use of such
materials or cleaning without consultation will invalidate the product
warranty. As dry cleaning is also risky for Anti‐Reflective (AR) coated
module surface, spinning brush is not recommended for module
cleaning.
128 CELL COMMERCIAL MODULE
1046 mm
4X Ø4.8 mm
1002 mm
Drain Holes
4X Ø4.2 mm
Ground Holes
20X Ø6.8 mm
Mounting Holes
300 mm
(Back View)
4X Ø6.10 mm
Stacking Pins
398 mm
(Front View)
3,2 mm
46 mm
MAXEON SOLAR TECHNOLOGIES, LTD.
Frame Profile
SIDE FRAME PROFILE
10.30 mm
46.08 mm
18.50 mm
32 mm
END FRAME PROFILE
10.50 mm
Method 1:
Frame Hole
46.08 mm
Locations
22 mm
SIDE FRAME PROFILE
10.30 mm
3.18 mm
46.08 mm
32 mm
With Stacking Pins
END FRAME PROFILE
10.50 mm
46.08 mm
22 mm
2.20 mm
1.27 mm
18.50 mm
2.20 mm
1.27 mm