Publicité
Single-Button
000-
000-
P1 - P1
099
099
000-
000-
P2 - P2
100
100
004-
004-
P3 - P3
136
136
004-
004-
P4 - P4
137
137
004-
004-
P5 - P5
138
138
004-
004-
P6 - P6
139
139
004-
004-
P7 - P7
140
140
004-
004-
P8 - P8
141
141
Double-Button
004-
000-
P3 - P1
136
099
004-
000-
P4 - P2
137
100
004-
004-
P9 - P5
142
138
004-
004-
P10 - P6
143
139
004-
004-
P11 - P7
144
140
004-
004-
P12 - P8
145
141
004-
004-
P17 - P13
150
146
004-
004-
P18 - P14
151
147
To complete the programming, you must pro-
gram t he button P7 w ith t he fi rst address of t he
third group (Block 007 Device 150) by entering
the following values:
----------------------------------------------
223+P1+007+P7(>4sec.)+224+P1+150+P7(>4sec.)
----------------------------------------------
after this phase the buttons will call the de-
sired addresses:
Single_Button
000-
000-
P1 - P1
099
099
000-
000-
P2 - P2
100
100
004-
004-
P3 - P3
136
136
004-
004-
P4 - P4
137
137
004-
004-
P5 - P5
138
138
004-
004-
P6 - P6
139
139
007-
007-
P7 - P7
150
150
007-
007-
P8 - P8
151
151
Double-Button
004-
000-
P3 - P1
136
099
004-
000-
P4 - P2
137
100
007-
004-
P9 - P5
152
138
007-
004-
P10 - P6
153
139
007-
007-
P11 - P7
154
150
007-
007-
P12 - P8
155
151
007-
007-
P17 - P13
160
156
007-
007-
P18 - P14
161
157
Continue with the next programming or exit
programming.
Muting the call in progress tone (code
323)
When the call is sent, the external door station
emits a call in progress tone when the indoor
station rings. This tone, if not desired, can be
muted through the steps described below.
enter code 323;
press button 1/ to confirm;
to enable muting enter the value 111; to
disable muting enter the value 222;
press button 1/ to confirm;
continue with the next programming or exit
programming.
Closing the call when the door lock open-
ing command is received (code 324)
The Cx2124AB module can be programmed
to close the conversation with the internal
station when the door lock opening command
is received. The function can be enabled using
the steps described below.
Enter code 324;
press button 1/ to confirm;
to enable the function enter the value 111;
to disable the function enter the value 222;
press button 1/ to confirm;
continue with the next programming or exit
programming.
Video intercom programming
The FARFISA DUO systems and the ALBA series
push-buttons panel allow you to quickly and
easily program the intercoms or video-in-
tercoms inside the apartments. Simplified
programming procedures differ depending
on whether they are intercoms or video in-
tercoms with automatic or manual address
programming.
Video intercom systems with automatic
address programming
Arrange the intercom or video-intercom for
automatic programming (see the relevant
product manual);
on the door station, press the button to which
you want to associate the call;
on the intercom or video-intercom, exit the
automatic programming (see the relevant
product manual);
proceed in the same way for all devices to
be programmed.
Video intercom system with manual ad-
dress programming
Note the address that is called by the door
station buttons as shown in the following
figures, depending on whether it is a single
or double button door station;
on the intercom or video-intercom, move the
micro-switches in order to set the address
associated with the call button that is to
be assigned to the device (see the relevant
product manual);
proceed in the same way for all devices to
be programmed.
Single-Button
109
110
099
111
100
112
101
113
102
114
103
115
104
116
105
117
106
118
107
119
108
120
Double-Button
123
119
124
120
101
099
125
121
102
100
126
122
107
103
131
127
108
104
128
132
109
105
133
129
110
106
134
130
111
115
139
135
116
112
140
136
117
113
141
137
118
114
142 138
Mi 2530/1
121
122
123
124
125
126
127
128
129
130
131
132
147
143
148
144
149
145
150
146
155
151
152
156
157
153
158
154
163
159
164
160
165
161
166 162
- 27 -
Publicité
