IMG STAGELINE CU-3IR Notice page 4

CU-3IR
Order No. 38.4060
4.2 Selecting the control programme
For direct selection of the 29 programmes,
press the coloured buttons (12) [repeatedly].
Button
R constant red
G constant green
B constant blue
Y constant yellow
C constant cyan
P constant purple
G R B constant white
To run through the control programmes suc-
cessively, press the button AUTO (8). The
programmes with the LEDs constantly light-
ing are skipped.
To switch between different programmes,
the buttons MODE (7) can also be actuated.
To switch from the programme constant light-
ing in red to the function for running through
all programmes, press the button MODE
6 Button ON for switching on
7 Buttons MODE for selection of a control
programme
8 Button AUTO: for running through the
control programmes successively
9 Buttons SPEED for the speed (9 levels)
10 Button OFF for switching off
11 Buttons BRIGHT for the brightness (9 lev-
els) for the programmes change of colour,
flashing and constant colour
12 Buttons for direct selection of the 29 con-
trol programmes (see chapter 4.2)
13 Button PAUSE to interrupt / continue the
programme run
14 Button RESET to reset the control to the
initial state (keep button pressed longer)
®
Copyright
All manuals and user guides at all-guides.com
Press the button repeatedly to switch between the programmes of a line
red becoming
brighter and darker
green becoming
brighter and darker
blue becoming
brighter and darker
yellow becoming
brighter and darker
cyan becoming
brighter and darker
purple becoming
brighter and darker
gradual transition
between all colours
4.3 Brightness, speed, pause, reset,
on / off
1) To adjust the LED brightness, press the
buttons BRIGHT (11). 9 levels are avail-
able. However, the brightness can only be
adjusted for the programmes change of
colour, flashing and constant colour. For
the remaining programmes the brightness
.
is exclusively defined by the programme.
2) Adjust the running speed with the buttons
SPEED (9). Nine speed levels are avail-
able.
6
O N
7
MODE MODE
R
Y
8
AUTO
© by MONACOR INTERNATIONAL GmbH & Co. KG, Bremen, Germany. All rights reserved.
flashing in red
flashing in green
flashing in blue
gradual transition
flashing in yellow
gradual transition
flashing in cyan
blue – green
gradual transition
flashing in purple
change of colour
change of colour
red – green – yellow – blue
red – blue – green
– purple – cyan – white
3) The button PAUSE (13) allows to stop and
4) By keeping the button RESET (14) pressed
5) To switch off the LEDs, press the button
5 Specifications
9
Power rating: . . . . . 10 A max.
10
Power supply: . . . . 12 – 24 V ,
O F F
No-load current: . . . approx. 100 mA
11
SPEED SPEED BRIGHT BRIGHT
Ambient
temperature: . . . . . . 0 – 40 °C
Dimensions: . . . . . . 115 × 55 × 20 mm
G B
12
Weight: . . . . . . . . . . 185 g
C P
R R
G G
B B
13
14
PAUSE RESET
Subject to technical modification.
CU-3IR
change of colour
green – red green – red
change of colour
blue – green
change of colour
red – blue red – blue
white becoming
brighter and darker
restart the run of the control programme.
for a few seconds, the control is reset to the
initial state. Then the brightness of the
LEDs is set to the maximum value and the
running speed to the medium value and the
unit is switched to the function for running
through all programmes.
OFF (10); to switch them on again, press
the button ON (6).
depending on the
LEDs connected
A-1013.99.02.02.2011