GRAPHITE 58G019 Traduction De La Notice Originale page 10

with clean water, you can also neutralize the liquid with a mild acid, e.g.
lemon juice or vinegar.
- When the liquid gets into eyes, wash it immediately with a lot of clean
water for at least 10 minutes. Seek medical advice.
• Do not use damaged or modified battery. Damaged or modified
batteries may behave unpredictably, causing fire, explosion or risk of
injuries.
• Do not expose the battery to humidity or water.
• Always keep the battery away from sources of heat. Do not leave
the battery for a long time in high temperature (in direct sunlight, in
proximity of heaters and wherever the temperature exceeds 50°C).
• Do not expose the battery to fire or excessive temperature.
Exposure to fire or temperature above 130°C may cause explosion.
CAUTION! Temperature of 130°C can be also defined as 265°F.
• Observe all charging instructions. Do not charge the battery in
temperature outside of range defined in the rating data table from
the instruction manual. Incorrect charging or charging in temperature
outside of defined range may damage the battery and increase the risk of fire.
BATTERY REPAIRS
• Do not repair damaged batteries. Battery can be repaired only by the
manufacturer or in an authorised workshop.
• When disposing of the worn out battery, take it to a service point
where you can utilize such dangerous wastes.
SAFETY REGULATIONS FOR THE CHARGER
• Do not expose the charger to humidity or water. Ingress of water
into the charger increases risk of electric shock. Use the charger only in dry
rooms.
• Disconnect the charger from power supply before starting any
maintenance or cleaning.
• Do not use the charger when placed on flammable surface (e.g.
paper, textiles) or in proximity of flammable substance. Greater
charger temperature when charging increases risk of fire.
• Check condition of the charger, cable and plug before each use.
Do not use the charger if any damage is found. Do not try to
disassemble the charger. All repairs should be made at an authorized
service workshop. Improper charger assembly may cause electric shock or
fire.
• Children or persons who are physically, emotionally or mentally
disabled and other persons, whose experience or knowledge is
insufficient to use the charger while following all safety rules should
not use the charger without supervision of person responsible for
their safety. Otherwise there is a risk of improper use and injuries in
consequence.
• When the charger is not in use, it should be disconnected from the
mains network.
• Observe all charging instructions. Do not charge the battery in
temperature outside of range defined in the rating data table from
the instruction manual. Incorrect charging or charging in temperature
outside of defined range may damage the battery and increase the risk of
fire.
CHARGER REPAIRS
• Do not repair damaged charger. The charger can be repaired only by
the manufacturer or in an authorised workshop.
• When disposing of the worn out charger, take it to a service point
where you can utilize such wastes.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always a
small risk of injuries at work.
Li-Ion batteries may leak, set on fire or explode when heated to high
temperature or short-circuited. Do not store the batteries in a car in
hot and sunny days. Do not open the battery. Li-Ion batteries contain
electronic protection devices that, if damaged, may cause fire or
explosion of the battery.
Explanation of used symbols
1
5
9
Read instruction manual, observe warnings and safety conditions
1.
therein.
Use protective goggles and hearing protectors.
2.
Keep the tool away from children.
3.
Protect against rain.
4.
Use indoors, protect from water and moisture.
5.
Recycling.
6.
Protection class 2.
7.
Segregated waste collection.
8.
Do not throw cells into fire.
9.
Hazardous to water environment.
10.
Do not allow to heat above 50°C.
11.
CONSTRUCTION AND USE
Drill is a battery powered tool. Drive consists of a brushless DC motor
with planetary gear. Drill is designed for screwing in and out screws and
bolts in wood, metal, plastics and ceramics, and for drilling holes in these
materials. Cordless, battery-powered power tools are especially useful for
works in interior furnishing, adaptation of premises etc.
Use the power tool in accordance with the manufacturer's instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Quick-release chuck
1.
Ring of the quick release chuck
2.
Torque adjustment ring
3.
Gear switch
4.
Direction selector switch
5.
Holder
6.
Battery
7.
Battery lock button
8.
Switch
9.
Lighting
10.
LED diodes
11.
Charger
12.
Button for battery level indication
13.
Battery level indicator (LED)
14.
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
10
2 3
6 7
Max.
50°C
10 11
4
8