Dyson SV10 Guide D'utilisation page 14

Masquer les pouces Voir aussi pour SV10:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

USING YOUR DYSON APPLIANCE
PLEASE READ THE 'IMPORTANT SAFETY INSTRUCTIONS' IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
OPERATION
Do not use outdoors or on wet surfaces or to vacuum water or other liquids –
electric shock could occur.
Ensure the appliance remains upright in use. Dirt and debris may be released if
it is turned upside down.
Do not operate while checking for blockages as doing so may result in
personal injury.
For domestic indoor and car use only. Do not use it while the car is in motion or
while driving.
To operate the Max mode, locate the switch on the top of the appliance. Slide
the switch to the Max mode position.
To switch off Max mode, slide the switch back to the Powerful Suction
mode position.
This appliance has carbon fibre brushes. Take care if coming into contact with
them, as they may cause minor skin irritation. Wash your hands after handling
the brushes.
DOCKING STATION INSTALLATION
Use appropriate mounting hardware for your wall type and ensure that the
docking station is mounted securely. Ensure no pipe work (gas, water, air) or
electrical cables, wires or ductwork are located directly behind the mounting
area. The docking station must be mounted in accordance with regulations
and applicable codes/standards (provincial and local laws may apply). Dyson
recommends the use of protective clothing, eyeware and materials when
installing the docking station.
CARPETS OR HARD FLOORS
Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
The brush bar on the appliance can damage certain carpet types and floors.
Some carpets will fuzz if a rotating brush bar is used when vacuuming. If this
happens, we recommend vacuuming without the motorized floor tool and
consulting with your flooring manufacturer.
Before vacuuming highly polished floors, such as wood or linoleum, first check
that the underside of the floor tool and its brushes are free from foreign objects
that could cause marking.
LOOKING AFTER YOUR DYSON APPLIANCE
Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Helpline.
Only use parts recommended by Dyson. If you do not this could invalidate
your warranty.
Store the appliance indoors. Do not use or store it below 3˚C (37.4˚F). Ensure
the appliance is at room temperature before operating.
Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning
agents, polishes or air fresheners on any part of the appliance.
VACUUMING
Do not use without the clear bin and filters in place.
Fine dirt such as flour should only be vacuumed in very small amounts.
Do not use the appliance to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the appliance.
When vacuuming, certain carpets may generate small static charges in the
clear bin or wand. These are harmless and are not associated with the mains
electricity supply. To minimize any effect from this, do not put your hand or
insert any object into the clear bin unless you have first emptied it. Clean the
clear bin with a damp cloth only. (See 'Cleaning the clear bin'.)
Use extra care when cleaning on stairs.
Do not rest the appliance on chairs, tables, etc.
Do not press down on the nozzle with excessive force when using the appliance
as this may cause damage.
Do not leave the cleaner head in one place on delicate floors.
On waxed floors the movement of the cleaner head may create an uneven
lustre. If this happens, wipe with a damp cloth, polish the area with wax, and
wait for it to dry.
EMPTYING THE CLEAR BIN
Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
Ensure the appliance is disconnected from the charger before emptying the
clear bin. Be careful not to pull the 'ON' trigger.
To make emptying the clear bin easier, it is advisable to remove the wand and
floor tool.
To minimize dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
To release the dirt, hold the appliance by the handle, pull the red lever back and
lift upwards to release the cyclone. Continue until the bin base automatically
opens and releases the dirt.
Remove the clear bin carefully from the bag.
Seal the bag tightly, dispose as normal.
To close, push the cyclone downwards until it is in the normal position and
manually close the base of the bin – the base will click when it is securely
in place.
14
CLEANING THE CLEAR BIN
Ensure the appliance is disconnected from the charger before removing the
clear bin. Be careful not to pull the 'ON' trigger.
Remove the wand and floor tool.
To remove the cyclone, hold the appliance by the handle, pull the red lever
towards you and lift upwards until the bin opens, then push in the red button
located behind the cyclone and lift the cyclone out.
To detach the clear bin from the appliance, pull back on the red catch located
at the base, slide the clear bin down and carefully remove forwards from the
main body.
Clean the clear bin with a damp cloth only.
Do not use detergents, polishes or air fresheners to clean the clear bin.
Do not put the clear bin in a dishwasher.
Ensure the clear bin is completely dry before replacing.
To replace the clear bin, align the tabs on the clear bin with the grooves on the
main body and slide upwards into place until the catch clicks.
Slide the cyclone into the grooves of the main body and push downwards until
it is in its normal position and manually close the base of the bin – the base will
click when it is securely in place.
WASHABLE PARTS
Your appliance has washable parts, which require regular cleaning. Follow the
instructions below.
WASHING THE SOFT ROLLER
CLEANERHEAD BRUSHBARS
Your appliance has two washable brush bars, check and wash these regularly
according to the following instructions to maintain performance.
Ensure the appliance is disconnected from the charger before removing the
brush bar. Be careful not to pull the 'ON' trigger.
TO REMOVE, WASH AND REPLACE BRUSHBARS:
Please refer to the 'Washing the Brushbars' illustrations alongside the
instructions below.
Turn the cleaner head upside down so the underside of the cleaner head is
facing you. Use a coin to turn the fastener one quarter anti-clockwise to the
unlocked position.
Rotate the end cap to the open position. Gently slide the large brush bar away
from the cleaner head.
Remove the end cap from the large brush bar.
Lift out the small brush bar from the octagonal end and pull away from the
cleaner head.
Hold the brush bars under running water and gently rub to remove any lint
or dirt.
Stand both brush bars upright. Ensure the large brush bar is stood upright as
shown. Leave to dry completely for a minimum of 24 hours.
Before replacing, check that the brush bars are completely dry. Refit the small
brush bar before the large one. Insert the round end of the small brush bar into
place. Push down the octagonal end until it clicks into place.
Reattach the end cap to the brush bar.
Slide the large brush bar back onto the cleaner head, around the motor. The
end cap should be in the open position as shown. Once in place, rotate the end
cap back into the closed position.
Close the fastener by turning a quarter turn clockwise. Ensure that the fastener is
fully turned and the base plate and the brush bars are secure.
WASHING THE FILTERS
Your appliance has two washable filters; wash the filters at least once a month
according to the following instructions to maintain performance. More frequent
washing may be required where the user: vacuums fine dust, operates mainly in
'Powerful suction' mode, or uses the machine intensively.
WASHING FILTER A
Ensure the appliance is disconnected from the charger before removing the
filter. Be careful not to pull the 'ON' trigger.
Check and wash the filter regularly according to instructions to
maintain performance.
The filter may require more frequent washing if vacuuming fine dust or if used
mainly in 'POWERFUL SUCTION' mode.
To remove the filter, lift it out of the top of the appliance.
Wash the filter with cold water only.
Run water over the outside of the filter until the water runs clear.
Squeeze and twist with both hands to make sure the excess water is removed.
Lay the filter on its side to dry. Leave to dry completely for a minimum of
24 hours.
Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near an open flame.
To refit, place the dry filter back into the top of the appliance. Make sure it is
seated properly.
WASHING FILTER B
To remove the filter, twist anti clockwise to the open position and pull away from
the appliance.
Wash the inside of the filter under cold running water, rotating the filter to
ensure all pleats are covered.
Gently tap the filter against the side of the sink several times to remove
any debris.
Repeat this process 4-5 times until the filter is clean.
Place the filter upright, with the top of the filter facing upwards, and leave to dry
completely for a minimum of 24 hours.
To refit, return the filter to the open position and twist clockwise until it clicks
into place.

Hide quick links:

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

V9

Table des Matières