Publicité
E. Temperature unit button
G. Temperature decrease button
I. TURBO FAN indicator
K. Room temperature indicator
M. Selected heating level indicator
The remote control (7) operation way is same as buttons on control panel (6).
USAGE
1.Turn on the device by pressing by hand the power switch (1) on the left side of device.
2. Press the power button (A) to illuminate the control panel (6), the device is ready to operate now.
3. To set the heat output press the heat output button (B) the appropriate number of times, the required heat level setting is achieved:
- one time pressing means low heat setting - 750W heat output, it will be shown on control panel,
- two times pressing means middle heat setting - 1250W heat output, value will be shown on control panel,
- three times pressing means high heat setting - 2000W heat output, value will be shown on control panel,
- four times pressing means the device come into frost protection function, snowflake indicator (H) will be shown on control panel.
The frost-proof mode is turned on, 5° C / 41 ° F are a fixed temperature value, when the environment temperature is below 5° C /
41 ° F , the device will start heat mode automatically at 2000W heating level until room temperature reaches 9° C / 48 ° F. Later the
heating is turned off to standby, followed by cycling.
4. To switch the TURBO fan on, press the button (C), the fan indicator (I) will be illuminated. Fan starts to operate. To stops the fan
press the button (C) again.
5. To setting the period of time the device will switch off you can use timer function. To preset a switch off time press the timer button
(D) appropriate number of times to choose operation time between 1-24 hours. The device will switch off automatically after chosen
period of time.
6. To setting the temperature units (F/C) that means: F = Fahrenheit and C = Centigrade press the temperature units button (E) the
appropriate number of times until the required temperature units setting is achieved.
7. To increasing the temperature setting press the button (F) the appropriate number of times until the required increased
temperature setting is achieved. The selected temperature setting (J) is indicated on the control panel. The range of temperature is
5-37°C / 41-99°F.
8. To decrease the temperature setting press the button (G) the appropriate number of times until the required decreased
temperature setting is achieved. The selected temperature setting (J) is indicated on the control panel.
Note: the control panel (6) always shows the last set temperature (J) and present the room temperature (K). If the heat function
switches itself off then set temperature (J) had been achieved in the immediate area of the device.
When the room temperature (K) reaches the set temperature level (J), the heating element stops to work. When room temperature
(K) is 1 degrees over the set temperature level (J), the heating element also will stop to work. The heating element will begin
operating again only when the room temperature decreases 1 degrees with respect to the set temperature.
9. To switch off the device press power button (A) and next switch off the power switch (1).
After around 1 minute of last action the control panel (6) stops to illuminate but the device is operating according to last setting.
CLEANING AND MAINTENANCE
1. Always unplug the appliance from the power socket before cleaning.
2. If during cleaning items such as the power plug, thermostat, electrical contacts etc. are soaked before being used again, they
should be thoroughly dried.
3. Do not use aggressive detergents in the form of emulsions, lotions, pastes, etc. to clean the cabinet. They can, among other
things, remove the information graphic symbols, such as signs, warning signs, etc.
4. Ensure that the device has cooled down before cleaning.
5. When the device is not used for long periods of time, it should be protected against dust and stored in a clean dry place.
TECHNICAL DATA:
Voltage: 220-240V ~50/60Hz
Power: 1800-2000W
Max. Power: 2000W
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins.
Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the
environment. Do not dispose this appliance in the common waste bin.
"Caution Hot Surface" - The temperature of available surfaces may be
higher when the equipment is working, which means that the housing
elements become very hot during operation during operation, SAVE
CAREFUL !!!
DO NOT COVER« INSCRIPTION IMPORTANCE
The inscription on the device means that the device is not to be covered with clothing, blankets
and other textile products which could cause ignition.
WARNING: Do not use this equipment near bathtubs, showers, swimming
pools and similar water tanks.
F. Temperature increase button
H. Frost protection indicator
J. Selected temperature indicator
L. Time remaining indicator to turn off the device
8
Publicité
