Publicité
No.
Description
Bit 48 - Bit 63
AO13 = Analog value 13
Bit 64 - Bit 79
AO12 = Analog value 12
Bit 80 - Bit 95
AO11 = Analog value 11
Bit 96 - Bit 111
AO10 = Analog value 10
Bit 112 - Bit 127
AO9 = Analog value 9
Bit 128 - Bit 143
AO8 = Analog value 8
Bit 144 - Bit 159
AO7 = Analog value 7
Bit 160 - Bit 175
AO6 = Analog value 6
Bit 176 - Bit 191
AO5 = Analog value 5
Bit 192 - Bit 207
AO4 = Analog value 4
Bit 208 - Bit 223
AO3 = Analog value 3
Bit 224 - Bit 239
AO2 = Analog value 2
Bit 240 - Bit 255
AO1= Analog value 1
IO-Link version V1.1; Process data length: 32 Byte In, 0 Byte Out
For details of the process data structure and service data structure, please refer
to IODD document 8025244.
Einzelheiten zur Prozessdatenstruktur und Servicedatenstruktur finden Sie im
IODD-Dokument 8025244.
Per i dettagli sulla struttura dei dati di processo e di servizio, consultare il docu‐
mento IODD 8025244.
Pour plus de détails sur la structure des données process et des données de
service, voir le document 8025244 dans la description des appareils (IODD).
Encontrará las particularidades sobre la estructura de los datos de proceso y la
estructura de los datos de servicio en el documento IODD 8025244.
有关过程数据结构和服务数据结构的详细信息请参见 IODD 文件 8025244。
5
Troubleshooting
Störungsbehebung
Eliminazione difetti
Élimination des défauts
en
LED/fault pattern
Cause
Green power LED does not
No voltage or voltage below
light up
the limit values
Orange output-LEDs do not
no input/output connected
light up
or signal low (=0)
de
LED / Fehlerbild
Ursache
Grüne Betriebs-LED leuchtet
Keine Spannung oder Span‐
nicht
nung unterhalb der Grenz‐
werte
Orange Ausgangs-LEDs leuch‐
kein Eingang/Ausgang ange‐
ten nicht
schlossen oder Signal low
(=0)
it
LED / figura di errore
Causa
Il LED verde non si accende
nessuna tensione o tensione
al di sotto del valore soglia
I LED arancione non si accen‐
Nessun input/output colle‐
dono
gato o segnale basso (=0)
fr
LED / image du défaut
Cause
La LED d'alimentation verte
Pas de tension ou tension
ne s'allume pas
inférieure aux valeurs limites
Les LEDs oranges ne s'allu‐
aucune entrée/sortie raccor‐
ment pas
dée ou signal faible (=0)
es
LED / imagen de error
Causa
El LED de alimentación verde
Sin tensión o tensión por
no se ilumina
debajo de los valores límite
Los LED naranja no se ilumi‐
no hay entrada/salida
nan
conectada o señal baja (=0)
8025499.187N/2023-01-31/de
Datatype
Integer 16
Integer 16
Integer 16
Integer 16
Integer 16
Integer 16
Integer 16
Integer 16
Integer 16
Integer 16
Integer 16
Integer 16
Integer 16
Resolución de problemas
故障排除
Measures
Check the power supply,
check all electrical connec‐
tions (cables and plug con‐
nections)
check the input/output con‐
nections
Maßnahme
Spannungsversorgung prü‐
fen, den gesamten elektri‐
schen Anschluss prüfen (Lei‐
tungen und Steckerverbin‐
dungen)
Eingangs-/Ausgangsan‐
schlüsse prüfen
Provvedimento
Verificare la tensione di ali‐
mentazione e/o il collega‐
mento elettrico
Controllare i collegamenti di
entrata/uscita
Mesure
Contrôler l'alimentation élec‐
trique, contrôler tous les
branchements électriques
(câbles et connexions)
vérifier les raccordements
entrée/sortie
Acción
Comprobar la fuente de ali‐
mentación, comprobar toda
la conexión eléctrica (cables
y conectores)
comprobar las conexiones de
entrada/salida
zh
LED / 故障界面
原因
绿色 LED 电源灯不亮。
无电压或电压低于极限值
橙色 LED 灯不亮。
无输入/输出已连接或信号低
(=0)
6
UL Satisfaction Ratings WI180C-IOB01
UL satisfaction ratings: Current of output signals Q1, Q2 must not exceed 0.1 A
Pollution
Altitude
Power supply
Environment
If the equipment is used in a manner not specified by manufacturer, the protec‐
tion provided by the equipment may be impaired.
UL Satisfaction Ratings
Depending on the number of fiber amplifiers and
displacement sensor amplifier units connected to
the WI180C-IOB01, the total load current of the out
put and the ambient temperature are limited as follows:
When power is supplied from a master unit of the
fiber amplifier/the displacement sensor amplifier unit
WLL180T/KTL180/WLL80 series: up to 2 units
Input: 12...24 V DC, Max. 0.14 A Class 2
Output: 12...24 V DC, Max. 0.1 A Class 2
Maximum Ambient Temperature 55 °C
WLL180T/KTL180 series: up to 3 units
Input: 12...24 V DC, Max. 0.14 A Class 2
Output: 12...24 V DC, Max. 0.1 A Class 2
Maximum Ambient Temperature 55 °C
WLL180T/KTL180/WLL80 series: up to 5 units
Input: 12...24 V DC, Max. 0.14 A Class 2
Output: 12...24 V DC, Max. 0.1 A Class 2
Maximum Ambient Temperature 50 °C
WLL180T/KTL180 series and AOD1 series: up to 8 units
Input: 12...24 V DC, Max. 0.14 A Class 2
Output: 12...24 V DC, Max. 0.1 A Class 2
Maximum Ambient Temperature 50 °C
WLL180T/KTL180/WLL80 series and AOD1 series: up to 8 units
Input: 12...24 V DC, Max. 0.14 A Class 2
Output: 12...24 V DC, Max. 0.1 A Class 2
Maximum Ambient Temperature 45 °C
WLL180T/KTL180 series: up to 16 units
Input: 12...24 V DC, Max. 0.08 A Class 2
Output: 12...24 V DC, Max. 0.04 A Class 2
Maximum Ambient Temperature 45 °C
WLL180T/KTL180/WLL80 series: up to 16 units
Input: 12...24 V DC, Max. 0.08 A Class 2
Output: 12...24 V DC, Max. 0.04 A Class 2
Maximum Ambient Temperature 40 °C
When power is supplied from WI180C-IOB01
WLL180T/KTL180/WLL80 series: up to 2 units
Input: 12...24 V DC, Max. 0.284 A Class 2
Output: 12...24 V DC, Max. 0.1 A Class 2
Maximum Ambient Temperature 55 °C
WLL180T/KTL180 series: up to 3 units
Input: 12...24 V DC, Max. 0.296 A Class 2
Output: 12...24 V DC, Max. 0.04 A Class 2
Maximum Ambient Temperature 55 °C
WLL180T/KTL180/WLL80 series: up to 3 units
Input: 12...24 V DC, Max. 0.276 A Class 2
Output: 12...24 V DC, Max. 0.04 A Class 2
Maximum Ambient Temperature 50 °C
One WLL180T/KTL180/WLL80 series and one AOD1series.
Input: 12...24 V DC, Max. 0.292 A Class 2
Output: 12...24 V DC, Max. 0.1 A Class 2
Maximum Ambient Temperature 50 °C
措施
检查电源，检查整体电气连接
（导线和插头连接）
检查输入/输出连接
Pollution degree 2
Up to 2,000 m
SELV, LIM
Indoor use
IO-Link Gateway - WI180C-IOB01 | SICK
4
Publicité
