WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions. Do not
leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer's original
parts. Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer's instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
WARNING:
This product contains chemicals, including lead, known
to the state of California to cause birth defects and other reproductive
harm. Wash hands after handling.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
Parts, Piezas, Pièces
Pump gasket
Empaquetadura para labomba
O-ring
Pump gasket
Joint d'étanchéité de pompet
Anillo en "o"
Empaquetadura para labomba
Anneau torique
Joint d'étanchéité de pompe
Spring
Spring
Nut (2)
Check valve
Fibre gasket (2)
Resorte del émbolo
Resorte del émbolo
Tuerca
Válvula de retención
Boquilla abancio
Ressortde tige
Ressortde tige
Ecrou
Clapet anti-retour
Joint de fibre
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d'étanchéité (non inclus) 6-4627
1. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank
for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening
and could result in explosive bursting under pressure. If any of these signs are found, discard tank
immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20
strokes and inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed
Sk-1154-1
with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any
of these conditions are found, replace affected part with original manufacturer's part before using.
2. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and
tighten securely.
3. Pressurizing and Spraying
3A
3C
O-ring
Plunger cup
Anillo en "o"
Cupde émbolo
Anneau torique
Plongeur piston
3D
O-ring (2)
Cup disc
Washer
Anillo en "o"
Disco esparicidor
Arandela de soporte
Anneau torique
Disque d'ecartment
Rondelle
2-1200-3 (A) R0116
3B
TO LOCK HANDLE: Push handle
down to depress coil spring and turn
Lock
handle 1/4 turn clockwise, then allow
Position
handle to raise into lock position.
TO LOCK PUMP: Place pump prongs down into slots in funnel,
turn clamp clockwise to furthest position under bottom slot, then
turn handle clockwise until tightly locked and sealed in place.
TO UNLOCK PUMP: Turn handle counterclockwise until 3-prong clamp
is loose. Then rotate clamp counterclockwise to stop and lift out.
3. Pressurizing and Spraying, continued
3E
TO RELEASE HANDLE: Push down to depress coil spring and turn
handle counterclockwise 1/4 turn, then lift handle.
3F
Pump until you feel resistance.
4. To Release Pressure
1 Do: With pump facing away, turn locked handle counterclockwise until air begins to
escape. Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
5. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing
and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the wand and
nozzle are thoroughly rinsed with water after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through
opening incover.
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com