Connecting Water Supply; Connecting To The Drain - Beko WMB 71041 Manuel D'utilisation

kilograms. Place the product on a solid and flat
floor that has sufficient load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where
temperature may fall below 0ºC.
• Place the product at least 1 cm away from the
edges of other furniture.
Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement
by pulling the ribbon.
Removing the transportation locks
Do not remove the transportation locks before
A
taking out the packaging reinforcement.
Remove the transportation safety bolts before
A
operating the washing machine, otherwise, the
product will be damaged.
1. Loosen all the bolts with a spanner until they
rotate freely (C).
2. Remove transportation safety bolts by turning
them gently.
3. Attach the plastic covers supplied in the User
Manual bag into the holes on the rear panel. (P)
Keep the transportation safety bolts in a safe
C
place to reuse when the washing machine
needs to be moved again in the future.
Never move the product without the
C
transportation safety bolts properly fixed in
place!

Connecting water supply

The water supply pressure required to run the
C
product is between 1 to 10 bars (0.1 – 1 MPa).
It is necessary to have 10 – 80 liters of water
flowing from the fully open tap in one minute
to have your machine run smoothly. Attach a
pressure reducing valve if water pressure is
higher.
If you are going to use the double water-inlet
C
product as a single (cold) water-inlet unit, you
must install the supplied stopper to the hot
water valve before operating the product.
(Applies for the products supplied with a blind
stopper group.)
If you want to use both water inlets of the
C
product, connect the hot water hose after
removing the stopper and gasket group from
the hot water valve. (Applies for the products
supplied with a blind stopper group.)
Models with a single water inlet should not be
A
connected to the hot water tap. In such a case
the laundry will get damaged or the product will
switch to protection mode and will not operate.
Do not use old or used water inlet hoses on
A
the new product. It may cause stains on your
laundry.
1. Connect the special hoses supplied with the
product to the water inlets on the product. Red
hose (left) (max. 90 ºC) is for hot water inlet, blue
hose (right) (max. 25 ºC) is for cold water inlet.
Ensure that the cold and hot water connections
A
are made correctly when installing the product.
Otherwise, your laundry will come out hot at the
end of the washing process and wear out.
2. Tighten all hose nuts by hand. Never use a
wrench when tightening the nuts.
3. Open the taps completely after making the
hose connection to check for water leaks at
the connection points. If any leaks occur, turn
off the tap and remove the nut. Retighten the
nut carefully after checking the seal. To prevent
water leakages and damages caused by them,
keep the taps closed when the machine is not in
use.

Connecting to the drain

• The end of the drain hose must be directly
connected to the wastewater drain or to the
washbasin.
Your house will be flooded if the hose comes out
A
of its housing during water discharge. Moreover,
there is risk of scalding due to high washing
temperatures! To prevent such situations and to
ensure smooth water intake and discharge of
the machine, fix the end of the discharge hose
tightly so that it cannot come out.
• The hose should be attached to a height of at
least 40 cm, and 100 cm at most.
• In case the hose is elevated after laying it on
the floor level or close to the ground (less than
40 cm above the ground), water discharge
becomes more difficult and the laundry may
come out excessively wet. Therefore, follow the
heights described in the figure.
3
EN