Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Fitting
Instructions
MATERIALS
A
1
Cross Bar.
D
1
Left Side Arm
E
1
Right Side Arm
F
1
Centre Strut
G
1
Spreader Plate (Boot)
H
2
Spreader Plate (Chassis rails)
J
2
Bush 19mm O.D x 46mm Long
K
2
Bush 19mm O.D x 41mm Long
L
1
Bush 32mm O.D x 26mm Long
M
2
M12 x 80 x 1.75 Bolts, Nuts, Lock Washers and Flat Washers (25mm O.D)
N
2
M12 x 70 x 1.75 Bolts, Nuts, Lock Washers and Flat Washers (25mm O.D)
P
4
M10 x 30 x 1.5 Bolts, Nuts, Lock Washers and Flat Washers (20mm O.D)
Q
1
M16 x 65 x 2 Bolt, Nut, Lock Washer and Flat Washer
R
2
M10 x 30 x 1.5 Bolts, Nuts, Lock Washers and Flat Washers (20mm O.D)
S
1
Electrical Plate (ZEP2)
ZQ
1
Detachable Kit (ZQ2030)
FITTING
1. Remove inner floor trim, spare wheel and jack from boot.
2. Locate mounting points on underside of chassis rails and drill pilot hole through top face using holes on lower face as
guide. Drill out pilot holes in top chassis face to sufficient size to insert bolts (M).
3. Locate mounting points on bottom of spare wheel well (200mm centres). Pilot drill through boot floor using holes in lower
face as guide. Drill out pilot holes in boot floor to sufficient size to insert bushes (K).
4. Attach side arms (D) and (E) using fixings (M) with spreader plates (H) and bushes (J) in position shown, Note bushes (J)
are inserted from under side.
5. Attach cross bar (A) using fixings (P).
6. Attach centre strut (F) using fixings (R). Insert bushes (K) and attach spreader plate (G) using fixings (N).
7. Insert bush (L) between neck profile and vehicle towing eye, secure using fixing (Q). Tighten all Bolts.
8. Attach Neck (ZQ) and Electrical Plate (S) as per separate fitting instruction.
9. Refit spare wheel, jack and inner trim.
Note:
Please refer to the vehicle specification for the trailer weight and nose limits, which must be observed.
Recommended torque settings: Grade 8.8 - M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm, M14 - 150 Nm, M16 - 214 Nm
WITTER TOWBARS
Deeside Ind. Park, Deeside, CH5 2NY
Grade 10.9 – M12 – 139 Nm
www.witter-towbars.co.uk
For DAIHATSU CHARADE
For use with ZQ2030 Neck option only
TOWBAR
DH18AU
& CUORE
Issue 1

Publicité

loading

Sommaire des Matières pour Witter DH18AU

  • Page 1 Fitting TOWBAR DH18AU For DAIHATSU CHARADE Instructions & CUORE For use with ZQ2030 Neck option only MATERIALS Cross Bar. Left Side Arm Right Side Arm Centre Strut Spreader Plate (Boot) Spreader Plate (Chassis rails) Bush 19mm O.D x 46mm Long Bush 19mm O.D x 41mm Long...
  • Page 2 Notice de ATTELAGE DH18AU Pour DAIHATSU CHARADE Mont & CUORE Pour utiliser avec ferrure ZQ2030 uniquement MATERIELS Traverse principale Bras latérale gauche Bras latérale droite Support centrale Entretoise (coffre) Entretoise (longerons) Entretoise tubulaire Ø19mm x 46mm de long Entretoise tubulaire Ø19mm x 41mm de long Entretoise tubulaire Ø32mm x 26mm de long...