Technical Specifications - Videx 4000 Serie Mode D'emploi

4000 Series
Art. 4384
Speaker unit with built-in camera
Art. 4384X
Speaker unit with built-in camera & proximity key reader
CONNECTION TERMINALS SIGNALS
ART. 4384 VERSIONS
VID2
Video signal input (coax centre core)
GNDV Video signal ground (coax screen and 0V to camera)
Output to supply the external camera
+V2
if necessary
BUS
BUS Connection terminals
BUS
PTE
"Push to exit" active low input
GND
Ground
NO
Door open relay normally open contact
C
Door open relay common contact
+C Electric lock capacitor discharge output
35Vdc power supply input/output.
In case the use of Art. 2321, the module is powered
VAUX
locally and not from the BUS.
It can be used as a source power (up to 20mA) to drive
the Art. 4846 module backlight.
Door open relay normally closed
NC
contact
NO2
Door open relay normally open contact 2
C2
Door open relay common contact 2
ART. 4384X VERSIONS
VID2
Video signal input (coax centre core)
GNDV Video signal ground (coax screen and 0V to camera)
Output to supply the external camera
+V2
if necessary
BUS
BUS Connection terminals
BUS
PTE
"Push to exit" active low input
GND
Ground
NO
Door open relay normally open contact
C
Door open relay common contact
+C
Electric lock capacitor discharge output
35Vdc power supply input/output.
In case the use of Art. 2321, the module is powered
VAUX
locally and not from the BUS.
It can be used as a source power (up to 20mA) to drive
the Art. 4846 module backlight.
Door open relay normally closed
NC
contact
NO2
Door open relay normally open contact 2
C2
Door open relay common contact 2
GND
Ground
B
RS-485 serial interface
A
Art. 4384/4384X -
Installation instructions
HOW TO REMOVE/INSERT THE CARD NAME HOLDER
• To avoid damage to the module front plate, mask the side that
will be in contact with the screwdriver blade;
• Insert the screwdriver (flat side) into the card-holder hole as
shown in Fig. 8;
Max 12Vdc
• Move the screwdriver to the left as shown in Fig. 9 to extract
150mA
the card name holder;
• Edit the card name then replace it inside the holder and refit:
insert the holder inside its housing from the left or right side
then push the other side until it clips into place.
Max 12-24
Vac/dc 2A
Fig. 8
ADHESIVE GASKET PLACEMENT
Max 60Vdc Apply the
or 40Vac
ANTI-TAMPERING LOCKS FIXING
0.1A
Fit the anti-tampering locks
Max 12Vdc
150mA
Fig. 10
CLEANING OF THE PLATE
Use a clean and soft cloth. Use moderate warm water or non-ag-
Max 12-24
gressive cleansers.
Vac/dc 2A
Do not use:
• abrasive liquids
• chlorine-based liquids
• metal cleaning products
• antioxidant products

TECHNICAL SPECIFICATIONS

Call buttons:
Max 60Vdc
Memory TAG:
or 40Vac
0.1A
Power consumption:
Working voltage:
Working temperature: -20 +60 °C
- 7 -
Fig. 9
seal as shown in Fig. 10.
Y
as shown in Fig. 11.
W
Y
G
Fig. 11
Up to 42
Up to 50 (up to 1000 when using PC
software)
Stand-by:
Operating: 100+10mA for each 404x
Peak:
Supplied by the BUS line
W
60+10mA for each 404x
250mA
66251850 - V3.3 - 30/11/22