Safety Instructions - Rubi ND-180 Instructions De Montage

6.

3. SAFETY INSTRUCTIONS

WARNING!
Important! When using electrical apparatus, observe the
following safety measures in order to reduce the risk of
electric discharge, injuries and fire.
Read and observe all these instructions before using the
machine and keep these instructions somewhere safe!
KEEP THESE INSTRUCTIONS SOMEWHERE SAFE
3.1 Keep clean the work area
■
Disordered tables and areas are prone to damage.
3.2 Consider the work area environment
■
Do not expose tools to rain.
■
Do not use tools in damp or wet places.
■
Keep the work area well lit.
■
Do not use tools in the presence of flammable liquids or
gases.
3.3 To protect against electric shock
■
Avoid body contact with grounded surfaces or mass (pipes,
radiators, stoves, refrigerators).
3.4 Keep others away
■
Do not allow people, especially children , not workers ,
contact tool or extendable cables and keep them away from
the work area.
3.5 Storing the tools are not being used
■
When not in use, tools should be stored in a dry, locked
place out of reach of children.
3.6 Do not force tool
■
This one will job better and safer at the assigned mode
feature which is intended.
3.7 Use the correct tool
■
Do not force a small tool to do the job corresponding to
a heavy tool.
■
Do not use tools for purposes for which they are not
intended ; for example , do not use circular saws to cut tree
limbs or logs.
3.8 Dress appropriately
■
Do not use large clothes or jewelry that may be caught by
moving parts clothing.
■
AntiSlip footwear is recommended when working outdoors.
■
Wear protective hats for long hair.
3.9 Use protective equipment
■
Wear safety glasses.
■
Use masks to prevent dust if cutting operations can produce.
3.10 Connect dust extraction equipment
■
If devices for connection to dust extraction equipment
and collecting equipment are provided , ensure these are
connected and are used properly.
English
3.11 Do not ill-use the cables
■
WNever pull the cord to disconnect it from the conection
box. Keep cord away from heat, oil and sharp edges.
3.12 Ensure the work
■
When possible, use clamps or a vise to hold work. It's safer
than using your hand.
3.13 Do not extend your range too
■
Maintain a strong support on the ground and maintain
balance at all times.
3.14 Maintan tools with care
■
Keep tools sharp and clean for better and safer performance.
■
Follow instructions for lubricating and changing accessories.
■
Periodically review the tool and cables for damage repair
through an authorized service.
■
Examine extension cords periodically and replace if damaged.
■
Keep dry the handle and grips, clean ,and free of grease
and oil.
3.15 Disconnect tools
■
When not in use , disconnect the power tools before repair
as accessories such as blades, bits and cutters are changed.
3.16 Remove adjusting keys and wrenches
■
Getting used to check that adjusting keys are removed from
the tool before operating.
3.17 Avoiding an unintended start
■
Ensure that the switch is in "open" position when the tool
is plugged.
3.18 Use extensible outdoor cables
■
When the tool is used outdoors, use only extensible cables
for outdoor use , they are marked for that purpose.
3.19 Be carefull
■
Look what you doing, use common sense and do not work
with the tool when you are tired.
3.20 Check damaged parts
■
Before re- using the tool, it should be carefully checked to
determine that it will operate properly and will be suitable
for the role to which it is intended.
■
Check the alignment and fixing of moving parts, breakage of parts,
mounting, and other conditions that may affect its operation.
■
A guard or other part that is damaged should be properly
repaired or replaced by an authorized service center, unless
otherwise specified in this instruction manual indicated.
■
Defective switches must be replaced by an authorized service.
■
Do not use tool if switch does not turn on and off.
3.21 Warming
■
The use of any accessory or other supplement recommended
in this instruction manual may create a personal injury risk.
3.22 Make the tool service by qualified personnel
■
This power tool complies with the requirements of appropriate
security. Repairs should only be carried out by qualified
personnel using original spare parts, otherwise there could