Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Figure 14
Start Your Appliance
Your refrigerated drawers have been fitted with a Sentry
System™ refrigeration monitor. It is located at the top front
of the cabinet and can be accessed by opening the top
drawer. Your appliance will start upon initial plug-in. On
start the Sentry System™ monitor LED will flash amber.
This is normal. Press the "ON/OFF" button and the appli-
ance resets and the LED turns green. (Refer to Figure 14
above). To turn the unit ON/OFF, press and hold the "ON/
OFF" key for a minimum of 5 seconds.
Set Your Temperature Mode
This product can display either Fahrenheit or Celsius. To
do so, press the "
F/C" button on the display panel to
°
change from one to the other.
Set the desired temperature
The available temperature range of the unit is from 34° to
42°F (1° to 6° C). This range allows flexibility of tempera-
ture preferences and provides the ideal storing and serving
temperatures. The temperature is initially set in the factory
at 37° F (3° C). The temperature set point can be lowered
or raised by first pushing the "SET" button on the display
pad. A "SET" icon will be displayed in the temperature
display. Pressing and releasing either the "WARMER" or
"COLDER" buttons located on the display pad will raise or
lower the set temperature by one (1) degree at a time. As
with any refrigeration product, there will be slight tempera-
ture variance at different locations within the cabinet.
Load Your Appliance
Load your appliance with your desired items. Please note
that it may take up to 24 hours for your refrigerator to reach
the desired temperature once loaded. This will primarily
depend on the amount of contents loaded into the refrigera-
tor and the amount of opening and closings of the draw-
ers. Consider this when initially loading the drawers. Best
results will be obtained by first allowing the drawers to "pull
down" to your set temperature before loading the drawers.
Interior Light
The upper and lower interior lights make it easy to view
your food and beverages. The light will always come on
when either drawer is opened, except when unit is in Sab-
bath Mode.
Defrost Cycle
In order to maintain optimal performance, your refrigerator
must periodically enter a defrost cycle to clear frost buildup.
All manuals and user guides at all-guides.com
USING YOUR REFRIGERATOR DRAWERS
ON
OFF
Press and hold
Warmer
Set
Colder
Sabbath Mode
Your refrigerated drawers are equipped with a Sabbath
Mode feature. By activating this mode, you will be dis-
abling all displays, audible alarms and lights. To activate
the Sabbath Mode, press and hold the "SET" button while
pressing the "
F/C" button four (4) times within seven (7)
°
seconds. To disable the Sabbath Mode, repeat the pro-
cess. The Sabbath Mode will deactivate automatically after
72 hours.
Warning Alarms
The Sentry System™ monitor will let you know if your unit
is not functioning properly for the following reasons. Door
ajar, high or low temperature, and power failure. These
alarms are explained below.
Door Ajar Alarm
If the drawer has been left open for over five (5) minutes,
the alarm will sound and the LED will flash green. This will
stop as soon as the drawer is closed, or can be reset by
pressing the "ON/OFF" button.
High and Low Temperature
If your unit reaches temperatures outside normal operating
temperatures for your set point for more than one (1) hour,
an alarm will sound and the LED will flash red. This will
warn you that your contents have seen temperatures that
may not be conducive for long-term storage. This alarm can
be reset by pressing the "ON/OFF" button.
Power Failure
If your unit experiences a power failure, the LED will flash
amber until the alarm is reset by pressing the "ON/OFF"
button.
Reset Alarms
Press the "ON/OFF" button for approximately one (1) sec-
ond. This will reset all audible and display alarms when the
button is released.
Enable/Disable Sentry System™ Alarms
Press and hold the "SET" key for five (5) seconds to enable
or disable the Sentry System™alarms. LED will display
a steady green when enabled or a steady amber when
disabled.
15
Sentry System™
Power Failure-Flashing Amber
Sentry System™
F/C
High/Low Temp-Red
Press ON/OFF-Reset
Alarms OFF-Steady Amber
Monitor LED
Publicité
Table des Matières
