Home Screen - Salora LANGATON32 SO Mode D'emploi

DVBS Configuration Setting screen: Tuner, Band
frequency and User Defined. User Defined option
will be available if the Band frequency is set as User
Defined. Set these options if available and press the
Right directional button to proceed.
(*) This option may be named as Satellite type depending on
the country selection.
Depending on the country and satellite type selections
you made in the earlier steps of the initial setup
process, Load Preset List screen may be displayed
next. Highlight Load Preset List and press OK or the
Right directional button to proceed with the SatcoDX
installation. You can also skip this step by selecting
Skip option.
After the parameters on the DVBS Configuration
Setting screen are configured according to your
environment and preset list installation preference is
selected the next step may be Select Satellite screen.
You may be able to set up different satellites depending
on the selected antenna type and operator in the
previous steps. Highlight the desired satellite option
and press OK to set the parameters(*). The Satellite
Status of the first satellite option will be set as On. In
order to configure other settings of the satellite and to
enable scan this option should be set as On first. Press
Back button and select next satellite you want to set.
After you completed the configuration changes, press
the Right directional button to proceed.
(*) If you have a Direct satellite system, DiSEqC Set option
should be set as DiSEqC A.
If Load Preset List option is selected in the previous
step next steps will be skipped and the preset channel
list installation will start. If the correct satellite has not
been selected for SatcoDX installation, a warning
dialogue will be displayed on the screen. The satellite/s
that can be selected will be listed. Press OK to close
the dialogue and then set the satellite accordingly.
Channel Scan screen will be displayed next. Select
Scan and press OK or the Right directional button
to proceed with the scanning configurations. Select
Skip Scan to proceed without performing a scan and
complete the initial setup.
DVBS Scan Configure screen will be displayed next
if Scan option is selected. Following options will be
available: Scan Mode and Channels. You can choose
to perform a full scan or a network scan. Set the
Scan Mode accordingly. If you are going to perform a
network scan, make sure that you have adjusted the
Frequency, Symbol Rate (Ksym/s) and Polarisation
parameters under the Transponder option accurately
on the Satellite Setup screen. You may not be able
to change the Scan mode setting depending on the
previous selections. If the Channels option is set
as Free encrypted channels will not be installed.
Additional options may also be available depending
on the selected operator, configure these settings
according to your preferences. Once you are done
with setting the available options, press the Right
directional button to start scan while Scan Mode or
Channels is highlighted. While the search continues
you can press the Back button to cancel the search.
The channels that have already been found will be
stored in the channel list.
When the initial setup is completed results will be
displayed. Press OK to finish the setup.
Home Screen will be displayed. You can press the Exit
button on the remote or highlight the Live TV app from
the Apps row on the Home Screen and press OK to
switch to Live TV mode and watch TV channels. For
some countries, the Live TV app will be situated in the
Home tab on the Home Screen and the row with this
app will be named as Favourite Apps.

Home Screen

To enjoy the benefits of your Android TV, your TV must
be connected to the Internet. Connect the TV to a home
network with a high-speed Internet connection. You
can connect your TV wirelessly to your modem/router.
Refer to the Network & Internet and Connecting to
the Internet sections for further information on how
to connect your TV to the internet.
The Home menu is the centre of your TV. Press the
Home button to display Home Screen. From the
Home menu you can start any application, switch to a
TV channel, watch a movie or switch to a connected
device. Depending on your TV setup and your country
selection in the initial setup the Home menu may
contain different items.
The available options of the Home Screen are posi-
tioned in rows. To navigate through the Home Screen
options use the directional buttons on the remote.
Apps, YouTube, Google Play Movies & TV, Google
Play Music and Google Play related rows and rows of
the applications you have installed might be available.
Select a row then move the focus to the desired item
in the row. Press OK button to make a selection or to
enter a sub-menu.
On the upper left of the screen, search tools will be
located. You can choose either to type a word to start
a search via the virtual keyboard or try voice search
option if your remote has a built-in microphone.
Move the focus to the desired option and press OK
to proceed.
On the upper right of the screen, Notifications, Inputs,
Network & Internet (will be named as Connected or
Not Connected according to the current connection
status), Settings and the current time will be displayed.
You can configure your date and time preferences
using the Date & time menu options from the
Settings>Device Preferences menu.
English - 12 -