SEVERIN PG 8560 Mode D'emploi page 10

∙ This product complies with all binding CE labelling
directives.
Before using for the first time
∙ Remove any packaging materials and stickers from the
appliance.
∙ Clean the grill, water pan and wind-guard in hot water
and dry thoroughly.
∙ Assemble the appliance as described in Preparing the
unit.
∙ Let the grill heat up for approximately 10 minutes at
maximum power without any food (see Grilling). This
will remove the smell typically encountered when first
switching on a grill. A little smoke may be emitted; for
that reason, adequate ventilation should be ensured by
opening windows or balcony doors; an extractor hood is
also suitable.
Grill assembly
∙ Assemble the grill as shown in the diagrams:
∙ Place the water pan in the housing.
∙ Place the heating element with the connection box in
the water pan. The device is equipped with a safety
switch. If the connection box is not installed correctly,
the device cannot be brought into operation.
∙ Put on the grill.
∙ Insert the side catches on the wind-guard first and
then the rear catches into the openings on the water
pan (only for outdoor operation).
Base stand assembly
∙ For grill models with base stand, assemble the stand as
shown in the diagram:
∙ Place the four plastic feet on the four support legs.
∙ Insert the support legs into the U-supports.
∙ Attach the cross braces and tighten them with the
eight screws and wing nuts.
∙ Insert the storage rack.
∙ Ensure that the stand is stable.
∙ Place the assembled grill on top.
Preparing the unit
∙ Assemble the appliance as described in Grill assembly.
For grill models with base stand, refer to Base stand
assembly.
∙ Fill the water pan with water up to the "Max" marking
(maximum 1.1 litres). Water must never be poured
directly onto the heating element.
Hint!
When using the barbecue, top up the water in the water
pan regularly to make up for evaporation. Always unplug
the device before doing this!
∙ Connect the appliance to the mains.
∙ The unit is ready for use.
10
Light ring
Stainless steel version:
Blue light ring:
The heating element is switched off.
Red light ring:
The heating element is switched on.
Cast iron version:
During the grilling process the heating element cycles and
the light ring lights up alternately red and blue (on and off).
Grilling
∙ Set the rotary control to the select the desired position
between min und max. The light ring shows steady red.
∙ Let the appliance heat up for around 10 minutes, and
then place the food on the grill surface.
After grilling
∙ Always disconnect the unit from the mains and allow it to
cool down after grilling.
Cleaning and care
∙ Ensure that the grill is thoroughly cleaned after use.
∙ Before cleaning the grill, ensure it is disconnected from
the power supply and has completely cooled down.
∙ Do not use metallic pads or abrasive cleaning agents.
∙ Remove the wind screen and the grill and rinse them in
water, leave to soak if necessary.
∙ Remove the heating element with the junction box. To
avoid the risk of electric shock, do not clean the heating
element with water and do not immerse it in water. The
heating element with junction box may be wiped with a
slightly damp lint-free cloth.
∙ Remove the water pan and rinse it in water, leave to
soak if necessary.
∙ All other parts can be cleaned with a cloth soaked
in soapy water, and should be wiped completely dry
afterwards.
Disposal
Devices marked with this symbol must be
disposed of separately from your household
waste, as they contain valuable materials which
can be recycled. Proper disposal protects the
environment and human health. Your local authority or
retailer can provide information on the matter.