VONROC CD504DC Traduction De La Notice Originale page 6

EN
e) Do not use a battery pack or tool that is dama-
ged or modifi ed. Damaged or modifi ed batteries
may exhibit unpredictable behaviour resulting in
fi re, explosion or risk of injury.
f) Do not expose a battery pack or tool to fi re
or excessive temperature. Exposure to fi re or
temperature above 130 °C may cause explo-
sion. NOTE The temperature „130 °C" can be
replaced by the temperature „265 °F".
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specifi ed in the instructi-
ons. Charging improperly or at temperatures
outside the specifi ed range may damage the
battery and increase the risk of fi re.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
ADDITIONAL SAFETY WARNINGS FOR DRILLS
AND SCREW DRIVERS
Drill safety warnings
a) Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
b) Hold the power tool by insulated gripping sur-
faces, when performing an operation where the
cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
c) Brace the tool properly before use. This tool
produces a high output torque and without
properly bracing the tool during operation, loss
of control may occur resulting in personal injury.
D) Hold the power tool by insulated gripping surfa-
ces, when performing an operation where the
cutting accessory or fasteners may contact
hidden wiring. Cutting accessory contacting a
"live" wire may make exposed metal parts of
the power tool "live" and could give the opera-
tor an electric shock."
6
SAFETY INSTRUCTIONS WHEN USING LONG
DRILL BITS
a) Never operate at higher speed than the maxi-
mum speed rating of the drill bit. At higher
speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece,
resulting in personal injury.
b) Always start drilling at low speed and with the
bit tip in contact with the workpiece. At higher
speeds, the bit is likely to bend if allowed to
rotate freely without contacting the workpiece,
resulting in personal injury.
c) Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend causing breakage or loss of control, resul-
ting in personal injury.
SAFETY WARNINGS FOR BATTERY
a) Do not open the battery. Danger of short-circui-
ting.
b) Protect the battery against heat, e. g., against
continuous intense sunlight, fi re, water, and
moisture. Danger of explosion.
c) In case of damage and improper use of the bat-
tery, vapours may be emitted. Ventilate the area
and seek medical help in case of complaints.
The vapours can irritate the respiratory system.
d) Use the battery only in conjunction with your
Vonroc product. This measure alone protects
the battery against dangerous overload.
e) The battery can be damaged by pointed objects
such as nails or screwdrivers or by force applied
externally. An internal short circuit can occur and
the battery can burn, smoke, explode or overheat.
FOR THE CHARGER
Intended use
Charge only CD811AA type rechargeable battery
packs. Other types of batteries may burst causing
personal injury and damage.
a) The appliance is not to be used by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experien-
ce and knowledge, unless they have been given
supervision or instruction
b) Children being supervised not to play with the
appliance
c) Do not recharging non-rechargeable batteries!
d) During charging, batteries must be placed in
the well ventilated area!
WWW.VONROC.COM