Table des Matières
Publicité
DIRECTIONS FOR USE
1. For your own safety
This fan heater is an extra-heating in the house. It must be used according to this concept.
Make sure that your supply rating corresponds to what specified on the rating plate i.e. 230 V AC,
50 Hz.
Don't leave your home while the appliance is in function: ensure in this case that the switch is in
OFF (0) position and the thermostat is in minimum position "❄".
.
During function, place the heater in a safe position :
far (1 mt. ) from inflammable objects or furnitures;
-
if wall mounted, not fixed to wooden or synthetic plastic surfaces;
-
leaving the air outlet space free : 1 mt. of free space in front of the heater and 50 cm. of free
-
space behind it;
not located immediately below a socket-outlet.
-
Do not leave animals or children touch or play with the appliance. Pay attention! The air outlet grille
gets hot during operation (more than 80° C i.e. 17 5° F)
Take care, that children are not playing with packaging material (e.g. Plastic Bags)
WARNING: In order to avoid overheating, do not cover the heater. Do not hang anything on
WARNING: In order to avoid overheating, do not cover the heater. Do not hang anything on
the heater and do not cover it while it's working. This is clearly written on the cover of the product
or shown by the symbol
Do not use the heater in rooms with explosive gas or while using inflammable solvents or varnish
or glues.
If the cordset is damaged and you have to change it, do not do the job yourselves! Take the
product to an after sales authorised repair centre or to a person with similar skill and knowledge, in
order to avoid any risk of danger.
Do not use this heater close to showers, baths, swimming pools.
The appliance must be positioned so that the plug is always accessible.
2. Safe positioning
The appliance must be used only on a flat, stable surface.
The appliance must be not accessible for persons who are taking a bath or in the shower.
Do not place the cable under a carpet.
Mind that during function the cordset must be always completely pulled out.
4.1 Use of the heater , version with switch and thermostat
6
ENGLISH
Mind that during function
4.1 Use of the heater , v
ON - OFF
1000 W
1800 W
Oscillation:
Due to the oscillation (turning) a more equal temperature in the surrounding is achieved.
Never block the oscillation movement.
ON - OFF
1000 W
1800 W
6.3 Use of the thermostat
In a room where the temperature is too high (more than 30°C), it is normal that the thermostat will not
switch on the heater.
In a room where the temperature is too low (around 5°C or even less) it is also normal that the
thermostat will keep the appliance working until the temperature gets higher.
To select the right thermostat position we suggest you to
-
turn the thermostat in maximum position (clockwise);
-
leave the appliance working until the comfortable temperature is reached;
-
turn the knob anti clockwise until you hear a "click" and the appliance stops;
-
turn clockwise again the knob (just a little): in this position the thermostat will maintain the
comfortable temperature you have selected.
If the appliance is used for the first time there can be a little smoke due to some production
oil residues.
For your safety the appliance has an tip over switch.
A pendular cuts off the power when it tips over.
The clatter noise is no reclamation reason.
To clean the filter proceed as following (picture)
- Pull out the power plug;
- Press the filter button at the back of the product and pull it backwards;
- Remove the sponge filter from its holder;
- Clean the filter by water with wash power under the temperature of 30°C.
5. Safety in case of abnormal operation
In case of overheating the safety cut out protecting the heating element will automatically switch off
the appliance.
In this case the appliance stops working and the pilot light will remain switched on even if the
appliance is not working.
If this happens:
-
switch off the fan heater;
-
remove the causes of abnormal operation or overheating (i.e. obstacles in front of air inlet or air
outlet grille);
-
leave the heater cool down for 15/20 minutes;
-
switch on again the fan heater.
6. Maintenance
This fan heater does not require any particular maintenance.
We only recommend to clean at least twice a year the air inlet and air outlet grille with a vacuum
cleaner to remove dust from motor and heating element.
In case you need to repair it, please contact an authorised repairing center.
If the cordset is to be changed, please mind that a 2x1mm
2
H05VVF HAR cordset is to be used.
7
Publicité
Table des Matières
