Schlage ND25 Mode D'emploi
Masquer les pouces Voir aussi pour ND25:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

*P517-382*
P517-382
Blank Rose
Installation Preparation
Door preparation:
For door preparation use the template included in the package with the
lock. For additional information, visit the website.
www.allegion.com/us.
Contact Product Support at
1-877-671-7011.
ND25 Exit Lock
Adjustment
Plate
Latch
Strike
Chassis
Anti-Rotation
Plate
Optional Spacer
for 1⅜" Door (2)
Inside Spring
Cage
1
Install latch
The bevel must face toward the door stop.
Installation Instructions
Mounting
Screws (2)
Rose
Actual Size
Pin wrench
Inside Lever

Publicité

Table des Matières
loading

Sommaire des Matières pour Schlage ND25

  • Page 1 *P517-382* ND25 Exit Lock P517-382 Installation Instructions Adjustment Plate Pin wrench Blank Rose Chassis Anti-Rotation Plate Mounting Screws (2) Rose Inside Lever Optional Spacer Latch for 1⅜” Door (2) Strike Inside Spring Cage Installation Preparation Install latch The bevel must face toward the door stop.
  • Page 2: Adjustment

    Door Thickness Adjustment NOTE: If door thickness insert is missing, align the adjustment plate to marks on chassis: • For 1³⁄4” thick doors, NO ADJUSTMENT IS REQUIRED. Continue to step 2. Door • For 1 ⅜ ” thick doors, install the optional spacers (see steps 2 and 3). No Adjustment Thickness further adjustment is required.
  • Page 3: Important

    Install chassis/outside blank rose assembly Install inside spring cage assembly Latch prongs fit between slide and slide clip. Slide Clip Optional Spacer 1⅜” (35 mm) door ONLY Door Lever catch edge faces door edge. Slide Install inside rose Align dimple Rotate rose until and groove.
  • Page 4: Customer Service

    Install strike Check lock function Actual Size Customer Service 1-877-671-7011 www.allegion.com/us...
  • Page 5: Installer Le Verrou

    ND25 Cerradura de Salida ND25 Serrure de la Sortie Instrucciones de Instalación Instructions d’Installation Chasis Placa de cierre Châssis Plaque vierge Llave de espiga Clé à ergot Placa a ajuste Placa anti-rotación Tornillos Plaque de réglage Plaque anti-rotation de montaje...
  • Page 6: Épaisseur

    Ajuste del gorosor de la puerta NOTA: Si falta el inserto de espesor de la puerta, alinee la placa de ajuste con las marcas en el chasis. Réglage de l’épaisseur de la porte REMARQUE : Si le gabarit d’épaisseur de porte est •...
  • Page 7 Instale la placa de cierre y el chasis Instale del conjunto interior de la caja para el resorte Installer le plaque vierge et le châssis Installer la cage du ressort intérieur Los dientes del pestillo ajustan entre el deslizador y el gancho lateral. Retén de la Les languettes de verrou s’insèrent entre la glissière et l’attache de la manija hacia...
  • Page 8: Servicio Al Cliente

    Instale la placa de hembra Verifique la función de la cerradura Installer la gâche Vérifier le bon fonctionnement du verrou Servicio al cliente Service à la clientèle 1-877-671-7011 www.allegion.com/us Tamaño real Taille réelle © Allegion 2021 Printed in U.S.A. P517-382 Rev. 03/21-c...
  • Page 9 PAGE 3 PAGE 7 BEGINNING SHEET Additional Notes: Revision History Revision Description: C > Reactivate this item for use with ND25. No new instruction needed for Broccoli project implementation. No artwork or spec changes. 066546 069086 089268 Material Edited By...

Table des Matières