Schlage ND Série Instructions

*P515-185*
P515-185
All installations should be in accordance with local
electrical codes and national electrical code, NFPA 70.
ND-Series Electrified Lock
L For standard installation, see full instruction sheet.
Select the appropriate mode for the installation using the mode select switch located on the chassis. Note: When mode is switched (from EL to EU or EU to EL) the
lock requires a complete lock/unlock power cycle to synchronize to the proper mode.
EL, electrically locked (fail safe):
Outside knob/lever or both outside and inside knobs/levers (depending on function) will lock when power is applied. In the event of power failure, the opening will be unlocked.
EU, electrically unlocked (fail secure):
Outside knob/lever or both outside and inside knobs/levers (depending on function) will unlock when power is applied. In the event of power failure, the opening will be locked.
Electrical requirements:
The ND-Series electrified locks are powered by DC power only. DO NOT USE AC POWER.
• Voltage: 12 or 24 V DC (maximum 26.4 V, minimum 10.8 V)
• Holding current: 10 mA
• Peak current: 230 mA
• Operating temperature: 32°F to 120°F (0°C to 49°C)
• All power requirements shown are for single lock operation.
Maximum Total Wire Length
AWG 14
12 V 500' (152 m) 300' (91 m)
24 V
Note: Either lock wire may be attached to
either power supply terminal (+ or -).
Troubleshooting:
If lock does not operate –
• Ensure the lock is powered with DC power.
• Ensure the input voltage is between 10.8 and 26.4 volts DC.
• Do not use AC power.
Request-to-Exit (RX) Lock
RX utilizes a microswitch inside the lock case to detect rotation of the inside knob/lever. The switch then signals the use of the opening to the security system. Attach wires from
RX switch wire harness to an electrified hinge/EPT (not furnished). Refer to the Allegion Connect section below for wire identification. Electrical rating: 2 A, 30 V DC
RX Switch kit #N123-062 installation:
Attach switch assembly to pin on chassis using the screw (included
with kit).
Use RX anti-rotation plate (see inset).
RX
Allegion Connect
Allegion Connect, a factory-installed Molex
Molex connector may be cut off and the lock installed with traditional wire splicing methods.
WIRE COLOR AND FUNCTION
Pin Color Function
1 Black Power (auto detects GND, +12 or +24 V DC)
2 Red Power (auto detects GND, +12 or +24 V DC)
3 Purple RX NO (normally open)
4 Grey RX NC (normally closed)
5 White RX COM (common for RX)
6, 7, 8 Not used
© Allegion 2020
Printed in U.S.A.
P515-185 Rev. 05/20-k
ND-Series Electrified Locks
16 18 20
200' (61 m) 100' (30 m)
Up to 1000' (304 m)
Power
For RX
connector system, provides simplified installation and maintenance utilizing quick-connect harnesses and hinges. Alternatively, the
®
Variable length wiring
harness (6" to 192")
Mode
select
switch
⁵⁄₁₆" (8 mm)
1³⁄₈"
(35 mm)
Latch
C L
¹³⁄₁₆"
(21 mm)
1³⁄₈"
(35 mm)
¹¹⁄₁₆"
(17 mm)
2¹⁄₈" (54 mm)
⁵⁄₁₆" (8 mm)
5 6
7 8
1 2
3 4
EPT or electrified hinge
Customer Service
1-877-671-7011
Wiring Instructions and Specifications
Lock to hinge/EPT harness
(not furnished)
Electrified hinge/EPT
(not furnished)
12 or 24 V DC
Switch (not
furnished)
Door Preparation:
Important! Drill RX hole first.
2⁵⁄₈" (67 mm)
³⁄₄" (19 mm)
⁷⁄₈" (22 mm)
drill thru
(10 mm)
Drill this hole first
Drawing is not to scale.
6" wiring harness
To
Power
Supply
Servicio al cliente Service à la clientèle
www.allegion.com/us
Power supply
12 or 24 VDC
(not furnished)
³⁄₈"