SSS Siedle LM 611-X/1-0 Serie Mode D'emploi page 7

after a short period of operation this
effect disappears.
• The achieved degree of brightness
depends on the temperature.
1 Removing the light module:
Slide the catch "a" to the left, tilt the
light module downwards and
remove from the support plate.
2 Components of the
LM 611-X/1-...
The LM 611-X/1-... always
comprises:
b Light with connecting cable
c Retaining plate
d Sheet metal screws 4x
e Tensioning clamps, short 4x
f Tensioning clamps, long 4x
g Plain washers 4x
h Wood screws 4x
i Dowels 4x
j System key
LM 611-X/1-... wall mounting
Connection to the 230 V AC mains
may only be performed using the
unilaterally installed connecting
cable or a connecting cable of
identical type (H05RN-F2x0.75mm
To allow the lamp to also be
exchanged when in a connected
sate, a small loop of the connecting
cable should be accommodated
behind the retaining plate. To
accommodate this, sufficient storage
space must be provided, for example
in the form of a 70 mm dia. junction
box.
The Vario system is integrated and
the combination frame KR 611-...
mounted.
3 On the retaining plate, puncture
the film over the fixing holes „k".
4 (no illustration)
Insert the retaining plate into the
mounted combination frame, mark
the position of the fixing holes and
drill.
5 (no illustration)
Guide the connecting cable
2
(H 05RN-F 2x0.75 mm ) through the
retaining plate and pull into the
interior of the junction box provided
on site (terminal compartment IP 54)
using the tape.
6 (no illustration)
The MR 611-..., ISM 611-...,
LM 611-X/1-... etc. are always
mounted from top to bottom,
ensuring that the attached sealing
foil lies under the module support of
the module above in fish-scale
formation.
7 Insert the retaining plate in the
KR 611-... and mount on the wall
(the attached sealing foil must
always be at the top), paying
attention that the guiding holes „m"
in the retaining plate correspond to
those of the supporting edge.
8 (no illustration)
Store the excess cable of appr.
30 cm behind the retaining plate.
9 Insert the light: Suspend the light
on the underneath of the retaining
plate and close by hinging upwards.
10 Locking the light into position
„n", releasing „o".
11 (no illustration)
Connect the LM 611-X/1-... to the
230 V AC mains at the junction box.
Apply the strain relief device to the
power lead in the junction box and
2 ).
create the mains connection.
Mounting the LM 611-X/1-... in
the flush/surface-mounting or
free-standing housing.
The module may only be connected
to the 230 V AC mains using the
unilaterally installed connecting
cable or a connecting cable of
identical type (H 05RN-F
2
2x0.75 mm ). To allow the lamp
to also be connected when in a
connected state, a small loop of
the connecting cable should be
accommodated behind the
retaining plate. The GU 611-... offers
sufficient space for this.
To mount the LM 611-X/1-... in the
surface/flush-mount or free-standing
Vario housing, the provided
tensioning clamps „e"/"f" are
required for mounting the retaining
plate.
12 (no illustration)
Guide the connecting cable
(H 05RN-F 2x0.75 mm
retaining plate and draw into the
interior of the junction box (terminal
compartment) using the tape.
13 (no illustration)
Select the tensioning clamps. The
long tensioning clamps „f" are
required for frames with a greater
shank length. The shorter tensioning
clamps „c" are always used for
frames up to a size of KR 611-4/4-...
14 Define the clamping position of
the tensioning clamps on the
retaining plate, paying attention to
the direction of the nearest
reachable support edge.
15 (no illustration)
Using a tool (knife/screwdriver),
puncture the attached sealing foil
at the insertion points.
16 Insert the tensioning clamps from
the back and fix using the sheet
metal screws „d".
17 (no illustration)
The MR 611-..., ISM 611-...,
LM 611-X/1-... etc. are always
mounted from top to bottom,
ensuring that the attached sealing
foil lies under the module support of
the module above in fish-scale
formation.
18 Insert the retaining plate into
the frame in such a way that the
attached sealing foil is at the upper
edge and align at the guide holes on
the support edge. (see point "m")
19 Slide the tensioning clamp
behind the support edge and care-
fully tension with feeling using the
sheet metal screw.
20 (no illustration)
Correctly connect to the 230 V AC
mains.
2 ) through the
5