Toddler Mode - Joie every stage fx Manuel D'instructions

ii. Securing your Child in the Child Restraint Use Infant Insert
Detach the snaps on
the head support to
remove the head
portion of the insert.
We recommend using the full
infant insert while the baby
is 0-9 months or until they
outgrow the insert. The infant
insert increases side impact
protection.
1. While pressing the harness adjustment button, pull completely the two shoulder harnesses of the child
-1 & -2. Press the red button to disengage the buckle.
restraint 10 10
2. Place the child in the child restraint, pass both arms through the harnesses and engage the buckle.
3. Pull down the adjustment webbing and adjust it to the proper length to make sure your child is snugly
secured.
12
!
After the child is seated, recheck whether the shoulder harnesses are at the proper height.
!
Ensure that the harness is snugly secured.

Toddler Mode

(Forward Facing Mode/for Child between 9-18kg)
see images 13 - 24
! Please install the child restraint on the vehicle seat, and then put the child in the child restraint.
i. Installation for Toddler Mode
!
Please adjust the child restraint to proper angle (4 positions for toddler mode).
!
Please adjust the shoulder harnesses to proper height before installing the child restraint.
!
When installing and adjusting the safety belts, make sure that both the shoulder belt and the waist belt are not
twisted and will not keep the safety belts from being properly positioned.
a. For installation with 3-point-belt
1. Thread the safety belt through two seat belt back slots at the back of the child restraint.
14
2. Buckle the safety belt.
3. Open the lock-off device and insert the safety belt through it.
4. While pressing the child restraint, pull the belts to fasten the child restraint tightly and securely.
!
The child restraint can not be used if the vehicle safety belt buckle (female buckle end) is too long to anchor
the child restraint securely.
!
Please check by moving the child restraint back and forth.
b. For installation with ISOFIX (ISOFIX attachments and top tether)
1. Fit the ISOFIX attachments guides with the ISOFIX attachments anchor points.
2. Extend the ISOFIX attachments connectors by depressing on the release button
18
connector
9
Remove the head support
portion of the infant
insert when the child's
head no longer fits
comfortably.
Remove the body
portion of the infant
insert when the infant's
shoulders no longer fit
comfortably.
1
Remove the infant insert
cushion by detaching the
snaps to allow more space
when the infant does not
fit comfortably. The
cushion can be used
2
separately without being
attached to the insert to
bolster the infant's back
for more comfort.
-3
10
11
13
15
16
17
whilst pulling on the
!
Make sure that both ISOFIX attachments connectors are securely attached to their ISOFIX attachments anchor
points. The colors of the indicators on both ISOFIX attachments connectors should be completely green.
-1
18
!
Select the desired recline position before moving back against the vehicle seat, as once the top tether is
attached and tensioned, the recline angle will not be able to change without adjustment to the top tether.
3. Press the ISOFIX attachments release button and push the child restraint back against the vehicle seat until
tight.
4. To extend top tether for use, press button on tether adjuster and pull to lengthen.
!
Make sure that tether hook are securely attached to the anchorage fitting. The colors of the indicators on
tether strap adjuster should be completely green.
5. Connect the tether hook securely to the anchorage fitting.
!
If recline angle is adjusted, check the tension on the top tether, or loosen to adjust angle then re-tension.
Removing the child restraint from the vehicle
1. To remove from the vehicle press the ISOFIX attachments release button and pull the base away from
the back rest.
2. Then press and release the connectors from the vehicle's ISOFIX.
!
Store the ISOFIX connectors in the base.
!
When not in use, top tether strap and anchor should be properly stored in the pocket.
ii. Securing your Child in the Child Restraint
!
When installing the child restraint in the toddler mode, do not use the infant insert.
1. While pressing the harness adjustment button, pull completely the two shoulder harnesses of the child
23 -1 & 23 -2
restraint.
23
2. Press the red button to disengage the buckle.
3. Place the child in the child restraint and engage the buckle.
4. Pull down the adjustment webbing and adjust it to the proper length so that your child is snugly secured.
!
After the child is seated, recheck whether the shoulder harnesses are at proper height.
!
Ensure that the harness is snugly secured.
Junior Mode
(Forward Facing Mode / for Child 15–36kg)
see images 25 - 28
i. Installation for Junior Mode
!
DO NOT use the integral harness system when using the child restraint in junior mode.
!
Please adjust the shoulder harnesses to proper length before store the shoulder harnesses and buckle in
their storage compartments.
!
Please adjust the child restraint to proper angle (4 positions for junior mode).
!
When installing and adjusting the safety belts, make sure that both the shoulder belt and the waist belt are
not twisted.
1. Press the red button to disengage the buckle.
2. Remove the infant insert and crotch pad.
-1
3. Detach the snaps. 25
4. Lift the upper flap upward and pull the lower flap forward, and then store the shoulder harnesses and buckle
-2 & -3
in their storage compartments. 25 25
5. Pull the buckle to the back of the seat pad, and then store the buckle and buckle tongues in respective
-4
storage compartments.
25
6. Do reattach the snaps to recover the seat pad. The reassembled seat pad is shown as
ii. Securing your Child in the Child Restraint
a. For installation with 3-point-belt
1. Place the child in the child restraint and check whether the shoulder belt guides are at proper height.
2. Position shoulder belt through shoulder belt guide, pass waist belt through lap belt guidings. Fasten buckle
and pull the vehicle belt to tighten. 27
19
-1
19
20
21
-3
26
24
10