Turbosound Siena TSP-AN Serie Guide De Démarrage Rapide page 11

20
TSP-AN Series
Networking capability
All TSP-AN powered loudspeakers offer remote control via USB. The USB connection allows the user to configure and monitor all DSP parameters using dedicated
control software for PC.
The DSP firmware can also be updated via the USB connection. Visit turbosound.com for the latest firmware version.
TSP-AN speakers also offer proprietary ULTRANET networking capabilities through the ULTRANET IN and THRU connections using CAT5 cables with RJ45 connectors.
ULTRANET allows the user to transmit unidirectionally up to 16 independent channels of 24-bit audio throughout the TSP-AN system, as well as other
ULTRANET-equipped devices such as digital mixers and personal monitor systems. Up to 7 devices can be connected in series on a single ULTRANET cable.
MIDAS DL16
MIDAS M32
TSP-AN DSP Menu Structure
Fullrange
None
PROCESS EQ
Live
Speech
Playback
User
Low/ High Shelving
Sub menu
Parametric 1 & 2
None
XOVER
HP 120 Hz
HP 100 Hz
-
-
TSP118B
User
Freq
Sub Menu
Phase
Auto
FBQ
Single
Learn
Reset
Input
SETUP
INPUT
(page 1)
Volume
Sensitivity
Stand
POSITION
21
Quick Start Guide
Subwoofer Function
None Sets the frequency response to the default setting.
Live Sets the frequency response to a typical live sound setting.
Speech Sets the frequency response for optimal speech intelligibility.
Playback Sets the frequency response ideal for music playback.
Lets you define your own frequency response setting by
User
entering the corresponding sub menu.
Low/ High Shelving Lets you define a low and high shelving filter.
Lets you define a parametric bell-type EQ
Parametric 1 & 2
(Frequency, Qual. and Gain).
- Unit is set for default full range / subwoofer reproduction.
Preset with 120 Hz 24 dB / octave filter for crossover
LP 120 Hz
between subwoofer and full-range speakers.
Preset with 100 Hz 24 dB / octave filter for crossover
LP 100 Hz
between subwoofer and full-range speakers.
Preset with ideal settings for use in combination with
TSP122
TSP122 fullrange speaker.
Preset with ideal settings for use in combination with
TSP152
TSP152 fullrange speaker.
- Preset with high pass alignment for TSP118B subwoofer.
User crossover sub menu for combination with other
User
fullrange or subwoofer speaker systems
Select the desired crossover frequency:
Freq Fullrange systems: 75 Hz to 400 Hz
Subwoofer systems: 50 Hz to 150 Hz
Phase
Adjust the absolute phase (0° or 180°).
Automatically sets as many filters as required. Whenever a
Auto new feedback frequency is discovered, the first filter will be
released to attenuate the new frequency, and so forth.
Activates the FBQ (feedback detection) functionality,
Single
up to 8 feedback filters
Automatic procedure which searches for feedback frequencies
and locks settings after all 8 filters have been set.
WARNING!
Learn
Please use ear protection during
this procedure. The feedback signal
may approach the system's maximum
level, which may cause hearing damage!
Reset Resets all filters.
Lets you choose the audio input source. Choose between
Input Local (analogue Input) or ULTRANET (e.g., P16 monitoring
system or M32 audio via ULTRANET).
Adjusts the input gain. With ULTRANET digital inputs over
Volume
a range from+ 10 dB to - 30 dB. With analogue input from
0 dB to -∞ dB.
Adjusts input sensitivity for maximum output when using
Sensitivity an analogue source +4 dBu for normal operation,
+ 14 dBu for high level input.
For positioning the speaker on a pole mount stand
Floor
(fullrange) or on the floor (subwoofer).