Eaton WFSW15 Mode D'emploi

ENGLISH
WFSW15 - WI-FI SMART SWITCH
WARNINGS AND CAUTIONS:
• Turn OFF circuit breaker or remove
fuse(s) and test that power is OFF
before installation process.
• Never wire any electrical device with power
turned ON. Wiring switch HOT may cause
permanent damage to switch and void
warranty.
• If you are not sure about any part of these
instructions, please contact a licensed
electrician.
IMPORTANT: Wi-Fi Smart Switch will not work
or will be damaged if wired incorrectly, and
the warranty will be voided. Refer to the wiring
instructions provided.
CAUTION
• Use only with 120V AC 60 Hz.
• Do not exceed maximum rating of the switch as indicated on the device.
• Must be installed and used in accordance with electrical codes.
• If a bare copper or green ground connection is not available in the wall box, contact a
licensed electrician for installation.
• Use only #14 or #12 copper wire rated for at least 75°C with these devices.
DO NOT USE WITH ALUMINUM WIRE.
NOTE: The Wi-Fi Smart Switch is wired directly to the light fixture. For Multi-location applications (3-Way) a
regular 3-Way switch can be used.
ELECTRICAL RATINGS
Current Capacity: 15Amps | Voltage: 120Vac | Horsepower: 1/2HP | Frequency: 60Hz
WI-FI SMART SWITCH INSTALLATION INSTRUCTIONS:
GETTING STARTED
Download the Amazon Alexa App and use the quick start guide provided to start the installation process.
The LED indicator will stop blinking once the device is added to the Amazon Alexa App.
For more information, visit
www.eaton.com/smarthome
OPERATION INSTRUCTIONS
• Press the ON button to turn the lights ON
• Press the OFF button to turn the lights OFF
• When the lights are ON, press and hold the OFF button for 2 seconds until the LED indicator blinks. After a 10
second delay, the lights will fade off
FACTORY RESET: The switch can be reset to exclude the device from its network and will
restore the device to all factory defaults.
• Press and hold the ON button until the LED indicator blinks for the second time (30 secs).
• Release the button
• The LED indicator will start blinking again indicating the switch is not part of the Wi-Fi network
For more advanced features including adjusting the brightness level of the LED indi-
cator, please refer to our configuration parameters
WI-FI SMART SWITCH COLOR CHANGE KIT INSTRUCTIONS
INSTRUCTIONS POUR LA TROUSSE DE CHANGEMENT DE COULEUR DE L'INTERRUPTEUR INTELLIGENT WI-FI
INSTRUCCIONES DEL KIT DE CAMBIO DE COLOR DEL INTERRUPTOR INTELIGENTE CON CONEXIÓN WI-FI
EXPLODED VIEW FOR CCK
STEP 1: Squeeze top tabs on either side of the device
ÉTAPE 1 : Serrer les languettes supérieures des deux côtés de l'appareil
PASO 1: Encaje todas las pestañas superiores a cada lado del dispositivo
NOTE: Not all products include color change kits.
REMARQUE : Certains produits ne comprennent pas de trousse de changement de couleur.
NOTA: No todos los productos incluyen kits de cambio de color.
ON Button
Bouton marche
Botón ON (ENCENDIDO)
LED Indicator
Témoin à DEL
Indicador LED
OFF Button
Bouton arrêt
Botón OFF (APAGADO)
EXPLODED VIEW FOR CCK
STEP 2: Pull faceplate off
ÉTAPE 2 : Retirer le plateau de montage
PASO 2: Retire la placa frontal
DATA AND INFORMATION CONTAINED HEREIN ARE THE PROPERTY OF EATON
CORPORATION AND ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE
RESIDENTIAL AND WIRING DEVICES DIVISION
203 COOPER CIRCLE , PEACHTREE CITY, GEORGIA 30269
TITLE
Wi-Fi Smart Switch, White
SIZE SCALE DWG NO
COD-249
B 1:1
THIRD ANGLE PROJECTION
DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM
FRACTIONS 1/64
ENGLISH (IN)
DECIMALS .015
THIS IS AN ELECTRONIC CAD DRAWING.
METRIC (MM) DECIMALS .40 DO NOT REVISE MANUALLY.
ANGLES ALL 2 DO NOT SCALE DRAWING
WIRING DIAGRAMS
Single Location Control Installation (WFSW15)
Installation de la commande à un emplacement unique (WFSW15)
Instalación del control de ubicación única (WFSW15)
Neutral Neutral
Neutre
Neutre
Neutral
Neutral
Neutro Neutro
3-Way
3 voies
3-Way
3 vías
Ground
Mise à la terre
Ground
Tierra
Two Location Control Using a 3-Way Switch
Commande à deux emplacements liée à un interrupteur à 3 voies
Control de dos ubicaciones mediante un interruptor de 3 vías
Hot
Sous tension
Caliente
120V
Ground
Mise a la terre
Tierra
DATA AND INFORMATION CONTAINED HEREIN ARE THE PROPERTY OF EATON
CORPORATION AND ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE
RESIDENTIAL AND WIRING DEVICES DIVISION
203 COOPER CIRCLE , PEACHTREE CITY, GEORGIA 30269
TITLE
Wi-Fi Smart Switch, White
SHEET REV SIZE SCALE DWG NO SHEET REV
A COD-249 A
B 1:1
3 OF 3 3 OF 3
THIRD ANGLE PROJECTION
DIMENSIONS ARE IN INCHES
DIMENSIONS IN [ ] ARE IN MM
X.X
X.X
FRACTIONS 1/64 X.X
X.X
ENGLISH (IN)
DECIMALS .015
THIS IS AN ELECTRONIC CAD DRAWING.
METRIC (MM) DECIMALS .40
DO NOT REVISE MANUALLY.
DO NOT SCALE DRAWING
ANGLES ALL 2
Black Hot 120V
Noir Sous tension de 120 V
Black Caliente 120 V Hot 120V
Negro
Hot Hot
Sous tension
Caliente
Load
Charge
Carga Load
Light Fixture
Light Fixture
Luminaire
Luminaria
Traveler wire 1
Fil voyageur 1
Cable guía 1
Neutral
Neutre
Neutro
Neutral
Neutre
3-Way
Neutro
3 voies
3 vias
Common
Commun
Commu
Green
Vert
Verde
Traveler wire 2
Fil voyageur 2
Cable guía 2
STEP 3: Line up all tabs and snap the faceplate on
ÉTAPE 3 : Aligner toutes les languettes et encliqueter le plateau de
montage
PASO 3: Alinee todas las pestañas y encaje la placa frontal
www.eaton.com/wiringdevices
Black Hot
Noir Sous tension
Negro Caliente
120V
Load
Charge
Carga
Light Fixture
Luminaire
Luminaria
Ground
Mise a la terre
Tierra
Neutral
Neutre
Neutro
EXPLODED VIEW FOR CCK
www.eaton.com
EIS-0250-EFS (REV. B)