Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
INSTALLATION
CAUTION
We strongly recommend the removal of the
old wall sleeve and the installation of a new
Kenmore Wall Sleeve.
If you decide to keep the existing wall sleeve,
you have to redirect the louvers at the back of the
wall sleeve illustration. The use of pliers is
recommended. If you DO NOT redirect, you run
the risk of poor performance or product failure.
This is not covered under the terms of the
Kenmore warranty.
• Pick a location which will allow the conditioned air
to blow into the area you want. Good installation
with special attention to the proper position of the
unit will lessen the chance that service will be
needed.
ITEMS IN INSTALLATION HARDWARE
You may not need all parts in the kit. Discard
unused parts
ITEM (inches)
Plastic grille
Vertical insulation strip
Around Insulation Strips
Horizontal Insulation Strip 23
Support Block
Baffle
Shim
Trim Frame
Washer Screw
Nuts(Plastic)
Grille Rear
HOW TO INSTALL
Identify the existing wall sleeve before installing
1
the unit from the listed below.
Wall Sleeve Dimensions (inches)
Brand
Width
White-Westinghouse
Frigidaire
25-1/2
Carrier (52F series)
General Electric
/Hotpoint
Whirlpool
25-7/8
Fedders/Emerson
Sears/Kenmore
25-7/8 15-17/32 16-23/32
Emerson/Fedders
26-3/4
Carrier (51S Series)
25-3/4
Friedrich
All manuals and user guides at all-guides.com
INSTALLATION
Qty.
26
3 /
x 16
1 /
1
4
2
15
9 /
x 1
3 /
x 1
3 /
1
16
8
8
67
1 /
x 1
3 /
x
25 /
1
8
8
32
59
27 /
x 1
3 /
x 1
3 /
1
32
8
8
7 /32
x 1
3 /
x 1
3 /16
1
8
1
3 /
x 1
3 /
x 4
5 /
2
4
8
16
14 x 4
1 /
x
1 /
1
2
8
11
13 /
x 1 x
3 /
2
16
4
2
4
4
1
Height
Depth
16, 17-1/2
15-1/4
or 22
26
15-5/8
16-7/8
17-1/8
16-1/2
or 23
16-3/4
27
16-3/4
or 19-3/4
15-3/4
15
16-7/8
18-5/8
27
16-3/4
16-3/4
NOTE: All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition
and have a rear grille that securely attaches to
sleeve, or rear flange that serves as a stop for the
Air Conditioner.
Remove old air conditioner from existing wall
2
sleeve.
Clean the interior of an existing sleeve.
3
(Do not disturb seals.)
Wall sleeve must be securely fastened in wall
4
before installing the air conditioner. Use the
nails or screws through sleeve into wall, if
needed. Repaint sleeve if needed.
Prepare the wall sleeve for installation of the
5
unit. If you plan to use your existing wall sleeve,
and it is not Kenmore, use procedure B or C
below.
Procedure Brand
A
Sears/Kenmore
White-Westinghouse
Frigidaire Carrier
(52F series)
General Electric
B
/Hotpoint
Whirlpool
Carrier (51S series)
Fedders/Emerson
C
Emerson/Fedders
Friedrich
6
Install new unit into wall sleeve.
CAUTION: When installation is completed,
replacement unit MUST have a rearward slope as
shown. To achieve 1/4" slope, remove the backing
from the 11-13/16" shim strips and attach them as
shown below in Fig. 3. Place the higher portion of
shim to the front of the rib on base of wall sleeve.
1" high
Shim
6"
SHIM PLACEMENT
- 6 -
Depth(inches)
16-23/32
16, 17-1/2
or 22
16-7/8
17-1/8 or 23
18-5/8
16-3/4
or 19-3/4
15
16-3/4
3 / 4 " High
UNIT
Wall Sleeve
FRONT
1/4"
6"
UNIT INSTALLATION
FIG. 3
Publicité
Table des Matières
