Publicité
Les langues disponibles
Les langues disponibles
Electrical Connections
energized.
• 12-24VDC Models – Connect the power source positive (+) lead to the solid-colored red
wire and connect the power source negative (-) lead to the solid-colored black wire.
• 120-240VAC 50/60Hz Models – Connect the line (L or L1) power source lead to the solid-
colored black wire and connect the neutral (N or L2) power source lead to the solid-colored
gray wire. Connect ground to the green/yellow wire if required.
Electrical Connections for Color/Flash Pattern Combinations:
produce 16 different color/flash pattern combinations. The color/flash pattern wires are white
striped and are distinct from the solid-colored power wires. Use the table below to achieve
desired color/flash pattern combination.
WIRE
PATTERN
COMBINATIONS
0
NONE
1
Y
2
B
3
B Y
4
G
5
G
Y
6
G B
7
G B Y
8
R
9
R
Y
10
R
B
11
R
B Y
R G
12
R G
Y
13
R G B
14
R G B Y
15
Testing/Operating: After installation, test the system to verify each signal operates and
establish a program for periodic testing of the device. Provide copy of these instructions to all
operating personnel.
Ordering Replacement Parts and Accessories: Consult product datasheet online for an
updated list of replacement parts. If this product requires a part that is not available for purchase,
your unit must be repaired or replaced. The product's dome should be regularly inspected for
scratches or chips, and if damaged it must be replaced.
Technical Assistance:
signalsupport@fedsig.com.
Repair Service: A return authorization is required. Contact your Authorized Distributor or Federal
Signal Customer Support. Defective products under warranty will be repaired or replaced at
Federal Signal's discretion. Lamp failures excluded.
Product Returns: Returns require authorization from Federal Signal. Contact your Authorized
Distributor for more information on our return policy or to request a return.
2645 Federal Signal Drive, University Park, Illinois 60484
Additional translations available at signaling.fedsig.com
Traducciones adicionales disponibles en signaling.fedsig.com
Customer Support 1-800-344-4634+1-708-534-4756, iordersup@fedsig.com
Technical Support 1-800-755-7621+1-708-587-3587, signalsupport@fedsig.com
To avoid electrical shock, do not connect wires when circuits are
PATTERN DESCRIPTION
BLUE - 120FPM
AMBER - 60FPM
BLUE - SIMULATED STROBE
AMBER - STEADY-ON
GREEN - STEADY-ON
AMBER - 120FPM
GREEN - 60FPM
BLUE - STEADY-ON
RED - 120FPM
AMBER - SIMULATED STROBE
RED - 60FPM
BLUE - 60FPM
RED - STEADY-ON
RED - SIMULATED STROBE
GREEN - 120FPM
GREEN - SIMULATED STROBE
Contact our technical support team at +1-708-587-3587 or
Model FB2LED-QC can
Examples of How to Use the Color/Flash
Pattern Combination Table:
• To select BLUE–120FPM. No connection of the color
flash pattern wires is necessary. Leave all wires
unterminated.
• To select AMBER–60FPM. Connect the yellow/white
wire to the input power wire (red + or black Hot/Line).
Leave all other wires unterminated.
• To select BLUE–STEADY-ON. Connect the green/white
wire, blue/white wire, and yellow/white wires to the
input power wire (red + or black Hot/Line). Leave all
other wires unterminated.
• To select GREEN–SIMULATED STROBE. Connect the
red/white wire, green/white wire, blue/white wire, and
yellow/white wire to the input power wire (red + or
black Hot/Line). Leave all other wires unterminated.
25500718A Rev. A0 0621
Printed in U.S.A.
Publicité
