Publicité
Les langues disponibles
Les langues disponibles
Stand-Alone Sensor Dimmer /
Switch Programming *
ALL PROGRAMMING IS OPTIONAL
Programming is not required for default functionality
For set-up, programming, and troubleshooting with a
Vive system, please refer to the installation instructions
included with the Vive hub or at www.lutron.com/vive
* Stand-Alone refers to devices that have NOT been commissioned
into a Vive system. Features and Settings that are only available
on the Sensor Dimmer / Switch when installed in a Vive system
are not shown in this installation guide. Please refer to the Vive
documentation at www.lutron.com/Vive
Note: If a device is connected to a Vive system, settings can only be
configured through the Vive GUI and cannot be changed locally at
the device.
Default Settings
Timeout: 15 minutes
Sensor Mode: Occupancy (Auto-On / Auto-Off)
1
PIR Sensitivity: High
Occupied Level: 100%
Vacancy Level: 0%
Fixed ALD Level: Low (when in Fixed ALD mode)
To Check Existing Settings
2
To display the existing settings, tap the Timeout (
), Sensor Mode (
or PIR Sensitivity (
) button. The indicator LED (
) that corresponds to
IL
P
the existing setting will illuminate.
Tap button
Maestro
(on / off)
lutron.com
LEDs
1.844.588.7661
T
Turn Off Power
Arrêtez le Courant
Desconecte la
ML
Corriente
IL
Raise
R
Indicator LEDs
2
L
Timeout
4
Lower
P
M
PIR
sensitivity
Sensor
mode
1,4,7
PIR lens
Sensor LED
(behind lens)
Sensor dimmer shown
In order for proper function of device, the device orientation needs to be installed
like shown above.
1
Sensor Mode is locked as "Vacancy" in vacancy only models (MRF2S-8SDV010 and
MRF2S-8SSV) when in Stand-Alone.
Only available in Stand-Alone. Not available when used in a Vive system.
2
Only available with the sensor dimmer. Not available with sensor switch.
3
4
Available in Stand-Alone. When the device is used in a Vive system, these adjustments are
only available via the Vive software.
Learning ALD (Ambient Light Detection): Lights remain off if enough natural light is present.
5
If the lights turn on and the user does not want that much light, they can tap
5 seconds of entering the space. Similarly, if the lights do not turn on when entering a space
and the user wants more light, they can tap
T
within 5 seconds of entering the space.
Over time, the sensor will learn the preferred light level.
Fixed ALD: Lights turn on only when there is less than a set (locked) amount of natural light
6
available. The level can be adjusted in "Fixed ALD Level" settings.
7
This setting will override the sensor mode of the Radio Powr Savr occupancy / vacancy
sensor.
Lutron Electronics Co., Inc. 7200 Suter Road
Coopersburg, PA 18036-1299 USA
Default settings in bold
Change Basic Settings
1. Press and hold the desired programming button (
2. Tap the same programming button to cycle to your desired setting.
3. Press and hold the same programming button until the
M
Timeout
4
Sensor Mode
(determines when lights turn on)
30 minutes
Occupancy (Auto-ON / Auto-OFF)
15 minutes
Occupancy with Learning ALD
5 minutes
Occupancy with Fixed ALD
1 minute
Vacancy (Manual-ON / Auto-OFF)
Notes:
• The device will retain all basic and advanced programming settings if power is removed and then restored.
• ALD stands for Ambient Light Detect. See http://www.lutron.com/TechnicalDocumentLibrary/048687.pdf for more information.
Change Advanced Settings
For complete programming options and additional information, visit www.lutron.com/TechnicalDocumentLibrary/048687.pdf
High-End Trim
3, 4
100%
1. Press and hold
T
and
R
simultaneously until a
2. Press and hold
R
until the top
ML
is reached and the lights brighten no further.
55%
Alt
3. Hold or tap
to decrease the high-end trim level until the desired level is achieved. The top 3
L
30
m
15
5
high-end trim setting is within the adjustable range. If you want to increase the high-end trim during programming process, press
1
4. Press and hold
until the
turns off to lock your selection (about 6 seconds).
T
ML
PIR
Mode
Hi
Occ
Low-End Trim
3, 4
Lrn
Med
Low
Fixd
Min
Vac
1. Press and hold
T
and
L
simultaneously until a
2. Press and hold
L
until the bottom
ML
45%
Alt
3. Hold or tap
R
to increase the low-end trim until the desired level is achieved and / or all lights are on and stable (no flickering). The bottom
30
m
15
3
LEDs give visual feedback of where the low-end trim setting is within the adjustable range. If you want to decrease the low-end trim
5
ML
1%
1
during the programming process, press
),
PIR
M
Mode
Occ
Hi
4. Press and hold
until the
turns off to lock your selection (about 6 seconds).
T
ML
Med
Lrn
Fixd
Low
Min
Vac
Occupancy Level
1,3,4
The level at which the sensor dimmer dims up to when motion is detected. This level is adjustable from 1% to 100% within the range of the low-end and
high-end trims.
100%
1. Press and hold
M
and
R
simultaneously until a
2. Press and hold
until the top
is reached and the lights brighten no further.
R
ML
Alt
3. Hold or tap
L
to decrease the occupancy level until the desired light level is achieved. The 7
30
m
15
occupancy level setting is within the adjustable range. If you want to increase the occupancy level during programming process, press
5
1%
1
4. Press and hold
M
until the
turns off to lock your selection (about 6 seconds).
ML
Mode
PIR
Occ
Hi
3
Vacancy Level
Med
3, 4
Lrn
Fixd
Low
Min
Vac
The level at which the sensor dimmer dims to or turns off when motion has not been detected for the timeout period.
This level is adjustable from 1% to 100% within the range of the low-end and high-end trim or can be set to OFF.
1. Press and hold
and
L
simultaneously until a
100%
M
Alt
2. Press and hold
L
until the bottom
ML
Alt
Alt
2
3. To set the vacancy level to off, press and hold
30
m
15
level until the desired light level is achieved. The 7
5
0%
1
range. If you want to decrease the vacancy level during programming process, press
3
PIR
Mode
Occ
Hi
4. Press and hold
M
until the
turns off to lock your selection (about 6 seconds).
ML
Lrn
Med
Low
Fixd
Vac
Fixed ALD Level
Min
1,2,6
The light level that determines when a sensor will turn lights on or keep lights off when detecting occupancy.
This setting only affects sensors set to "Fixed ALD" mode.
4
High (turn ON lights unless area has a lot of light)
Medium
Low
Minimum (turn ON lights only when room is dark)
1. Press and hold
and
simultaneously until an
begins to flash (about 3 seconds).
M
Alt
IL
Alt
2. The "Fixed ALD" light level will now be displayed by the
IL
30
m
3. Press and hold
M
or
until the
IL
turns solid to lock your selection (about 3 seconds).
Alt
15
Walk-through Mode
2
5
(MRF2S-8SD010 and MRF2S-8SS only)
1
Allows the lights to turn off before the Timeout has expired if occupancy is detected only briefly.
1. Press and hold
and
simultaneously until an
(unused)
Alt
(unused)
PIR
2. The walk-through setting will now be displayed by the
Mode
Disabled
Hi
Occ
3. Press and hold
or
until the
Alt
Enabled
Med
Lrn
Low
Electronic Off
Fixd
2,3
Min
Vac
Alt
Affects how the lights are turned off. If enabled, the driver remains powered, but the lights turn off. This requires that the driver supports this method of
T
within
control. If disabled, the driver has power removed every time the lights are turned off. All drivers support this method of control.
30
m
15
(unused)
1. Press and hold
and
M
simultaneously until an
5
(unused)
2. The electronic off setting will now be displayed by the
1
Enabled
3. Press and hold
or
until the
M
Disabled
PIR
Mode
Alt
Hi
Occ
Med
Lrn
30
m
Low
Fixd
Lutron, Radio Powr Savr, Pico, Maestro, and Vive are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the U.S. and other countries.
15
Min
Vac
App Store is a service mark of Apple, Inc. Android and Google Play are registered trademarks of Google LLC. iOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
5
© 2019 Lutron Electronics Co., Inc.
1
Customer Assistance | 1.844.LUTRON1 U.S.A. / Canada | +1.888.235.2910 Mexico | +1.610.282.3800 Others | www.lutron.com/support
,
, or
) until an
flashes (about 3 seconds).
M
P
IL
turns solid (about 3 seconds). The setting has been saved.
IL
P
1,4,7
PIR Sensitivity
4
High
2, 5
Medium
Low
2, 6
4
Minimum
flashes (about 6 seconds).
ML
LEDs give visual feedback of where the
ML
ML
flashes (about 6 seconds).
is reached and the lights dim down no further.
L
.
ML
begins to flash (about 6 seconds).
LEDs give visual feedback of where the
ML
begins to flash (about 6 seconds).
ML
is reached and the lights dim down no further.
L
until all
s flash (about 3 seconds). Otherwise, hold or tap
R
to increase the vacancy
ML
LEDs give visual feedback of where the vacancy level setting is within the adjustable
ML
L
.
. Tap
or
to cycle to your desired setting.
M
Alt
begins to flash (about 3 seconds).
IL
IL
. Tap
or
to cycle to the desired setting.
Alt
IL
turns solid to lock your selection (about 3 seconds).
IL
begins to flash (about 3 seconds).
. Tap
or
to cycle to the desired setting.
IL
M
turns solid to lock your selection (about 3 seconds).
IL
Test Mode
When in Test Mode, Occupancy has a short timeout (< 15 seconds) that can be used to test the coverage of the
sensor with the existing settings.
4
1. Wait at least 2 minutes after power is turned on.
2. Press and hold
until the Sensor LED under the PIR lens turns on (about 3 seconds). This indicates that you are
T
in test mode. Once you let go of
, the Sensor LED will go out. However, it will turn on with any detected motion
T
and stay on until the 15 second Timeout is allowed to expire.
3. The device will exit test mode after 5 minutes of inactivity or when
The sensor LED behind the lens will turn on while occupied and turn off while vacant.
Note: If you try to enter test mode within 2 minutes of turning on power, the Sensor LED will blink.
Reset Factory Default Settings
Note: It may be necessary to reset the device to factory default settings. Before beginning, ensure the device is
connected and powered.
Note: Any device associations or programming previously set up with the sensor dimmer / switch will be erased
and will need to be re-programmed after resetting to factory defaults.
R
.
1. Triple-tap
and hold until the
lights and the load lights begin to flash rapidly (for the switch) or brighten and
ML
T
dim rapidly (for the dimmer). Then release
.
T
2. Within 1 second of releasing
, rapidly tap
T
T
lights will begin to flash slowly (for the switch) or brighten and dim slowly (for the dimmer). This indicates that the
device will reset to factory defaults. Give the device about 10 seconds to complete the reset process.
Troubleshooting
Symptom
Possible Causes and Solutions
Lights cannot be manually turned
• Verify proper wiring. Neutral must be connected for product to function properly.
R
.
ON or OFF with the newly installed
• Wait 10 seconds and try to turn ON or OFF again.
sensor dimmer / switch.
• Wireless device is out of range.
Wireless device will not associate
• Wireless performance is being affected by the physical setup of the space.
to a sensor dimmer / switch.
See Wireless Communication section of this document for more information.
• Sensor modes are limited for vacancy only models
Not all of the sensor modes are
(MRF2S-8SDV010 and MRF2S-8SSV).
available when programming.
• Device may be part of a Vive system.
• Sensor Mode is set to Vacancy (Manual-ON / Auto-OFF).
• The sensor dimmer / switch may be a vacancy only model
(MRF2S-8SDV010 and MRF2S-8SSV).
Lights do not automatically turn
• The room may be too bright for the existing light level setting if in
ON when space is occupied.
Fixed ALD Occupancy Mode.
• The room may be too bright for the "learned" light level if in Learning ALD
Occupancy Mode.
Driver / ballast cannot be dimmed
• Verify proper connection of gray and purple wires.
up or down.
• Driver / ballast does not comply with IEC 60929 Annex E.2.
Lights flicker when dimmed all the
• Raise the low-end trim level of the dimmer until the lights no longer flicker when
way down.
fully dimmed.
is pressed.
T
three times again (release after third tap). The
lights and the load
ML
www.lutron.com/support
Publicité
