Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 23
10

Preparing to install

• Adjustable headrest
• Shoulder straps
• Baby insert
• Baby cushion
• Harness buckle
• Central adjuster
• Reclining handle
• Release handle headrest
• Installation screen
• Spirit level
• Battery compartment
• Floor support
• Floor support height indicator
• Height adjuster floor support
• Rotation release handle
• Switch for ISOfix connectors (2x)
• ISOfix connectors (2x)
• ISOfix release switch
• ISOfix indicators (2x)
• ISOfix car anchorage (2x)
Installation
1. When installing in the back seat of the vehicle, push the front seat of
the vehicle forward as far as possible and adjust the back rest into
an upright position (if it can be adjusted).
2. When installing in the front seat of the vehicle, adjust the back rest
into an upright position.
3. Position the vehicle on a horizontal surface when installing the seat.
4. When the base is lifted the floor support should fall downwards from
underneath the base. Do this outside the car.
5. Push down the switch for the ISOfix connectors at both sides to
release the ISOfix connectors. (2)
6. Position the base on the vehicle seat. Click the ISOfix connectors on
to the ISOfix anchorages on the vehicle seat. Make sure that both
ISOfix indicators are green. (3)
7. Push the seat towards the backrest of the vehicle seat until it
touches the backrest. (4)
8. The ISOfix connectors will have resistance sliding in, in the most
outward positions, before they are connected with the ISOfix
anchorage of the vehicle.
(1a)
(1b)
(1c)
(1d)
(1e)
(1f)
(1g)
(1h)
(1i)
(1j)
(1k)
(1l)
(1m)
(1n)
(1o)
(1p)
(1q)
(1r)
(1s)
(1t)
9. Tip: once the ISOfix connectors are installed, the seat can be
turned towards the door of the vehicle to get a better view on the
installation display.
10. Adjust the floor support, so it is in contact with the floor of the
vehicle. (5)
11. The height indicator of the floor support shows green when the floor
support is in contact with the floor. (5)
12. Lift the base at the front side (near the spirit level) and extend
the floor support till the spirit level is in the middle, indicating a
horizontal position of the base. (5)
13. Tip: place one foot onto the bottom end of the floor support while
lifting the base to make adjusting the length at this step easier.
14. The alarm sound stops when the floor support indicators show green
and it is in contact with the floor. Make sure that the horizontal spirit
level shows a horizontal position of the seat. (5)
15. When having the child seat installed rear facing in the back, it is
recommended to position the front vehicle seat in a way that it is
close to the touchpoint with the child seat. Make sure that the child
seat can still rotate freely.
When having the child seat installed rear facing on the passenger
seat in the front, it is recommended to position the passenger seat
in a way that the dashboard is close to the touchpoint with the child
seat. Make sure that the child seat can still rotate freely.
16. Tip: If you feel like the base has too much side movement, you can
install the seat tighter against the vehicle seat backrest. Make the
support leg short, grab the base and push it against the vehicle
backrest with more force. Move it side to side until you hear one
more 'click' per side, then lift the base into horizontal position again
17. The seat is delivered with removable SIP+ (side impact protection
+). This extra side impact protection should be used on the door side
of the vehicle. It can be connected by slotting between the seat shell
and the fabric. The seat already offers high level integrated side
impact protection. This extra side impact protection improves the
protection in the side impact still further. (Not on all models) (6)
18. Tip: For an optimal height of the SIP+, position it between the two
raised dots on the side of the seat shell.
19. Do not use the SIP+ on the seat when the space between seat and
door of the vehicle is too small, which might lead to a situation where
the seat is not positioned correctly on the vehicle seat.
11

Publicité

Table des Matières
loading

Table des Matières