Symbols In This Manual; Installation Notes - Sharp MX-B350P Guide De Démarrage

Symbols in this manual

To ensure safe use of the machine, this manual uses various
safety symbols. The safety symbols are classified as explained
below. Be sure you understand the meaning of the symbols
when reading the manual.
Meaning of the symbols
WARNING
Indicates a risk of death or
serious injury.
CAUTION! HOT
PINCH POINT KEEP
CLEAR
PROHIBITED
ACTIONS
Power notes
WARNING
Be sure to connect the power cord only to a power
outlet that meets the specified voltage and current
requirements. Also make certain the outlet is
properly grounded. Do not use an extension cord
or adapter to connect other devices to the power
outlet used by the machine.
Using an improper power supply may cause fire or
electrical shock.
* For the power supply requirements, see the name
plate on the left side of the machine.
Do not damage or modify the power cord.
Placing heavy objects on the power cord, pulling it, or
forcibly bending it will damage the cord, resulting in
fire or electrical shock.
Do not insert or remove the power plug with wet
hands.
This may cause electrical shock.
CAUTION
When removing the power plug from the outlet, do
not pull on the cord.
Pulling on the cord may cause damage such as wire
exposure and breakage, and may result in fire or
electrical shock.
If you will not use the machine for a long time, be
sure to remove the power plug from the outlet for
safety.
2
CAUTION
Indicates a risk of human
injury or property damage.
DO NOT
DISASSEMBLE
MANDATORY
ACTIONS
When moving the machine, switch off the main
power and remove the power plug from the outlet
before moving.
The cord may be damaged, will create a risk of fire or
electrical shock.

Installation notes

CAUTION
Do not install the machine on an unstable or
slanted surface. Install the machine on a surface
that can withstand the weight of the machine.
Risk of injury due to the machine falling or toppling.
If peripheral devices are to be installed, do not install
on an uneven floor, slanted surface, or otherwise
unstable surface. Danger of slippage, falling, and
toppling. Install the product on a flat, stable surface
that can withstand the weight of the product.
Do not install in a location with moisture or dust.
Risk of fire and electrical shock.
If dust enters the machine, dirty output and machine
failure may result.
Locations that are excessively hot, cold, humid, or
dry (near heaters, humidifiers, air conditioners, etc.)
The paper will become damp and condensation may form
inside the machine, causing misfeeds and dirty output.
If the location has an ultrasonic humidifier, use pure
water for humidifiers in the humidifier. If tap water is
used, minerals and other impurities will be emitted,
causing impurities to collect on the inside of the
machine and create dirty output.
When the machine is installed, the adjusters must
be lowered to the floor to secure the machine
(prevent it from moving).
Rotate the adjusters in the locking direction until they
are in firm contact with the floor.
If you find it necessary to reposition the machine
due to rearrangement of your office layout or
other reason, retract the adjusters from the floor,
turn off the power, and then move the machine.
(After moving the machine, lower the adjusters again
to secure the machine.)
Locations exposed to direct sunlight
Plastic parts may become deformed and dirty output
may result.
Locations with ammonia gas
Installing the machine next to a diazo copy machine
may cause dirty output.
Do not install the machine in a location with poor air
circulation.
A small amount of ozone is created inside the
machine during printing. The amount of ozone created
is not sufficient to be harmful; however, an unpleasant
odor may be noticed during large print runs, and thus
the machine should be installed in a room with a
ventilation fan or windows that provide sufficient air
circulation. (The odor may occasionally cause
headaches.)
* Install the machine so that people are not directly
exposed to exhaust from the machine. If installed near
a window, ensure that the machine not be exposed to
direct sunlight.