Panasonic WV-CS570/G Mode D'emploi page 50

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

After a blemish compensation position is set up, (*)
is attached at the right of the number.
3. If you would like to delete a blemish compensation
position, move the cursor to the applicable number
and press the CAM (SET) button.
The blemish compensation position setting screen
appears. Press the F3 button of WV-CU650 when
the setting screen is active.
For WV-RM70, hold down the right and left buttons
simultaneously for 2 seconds or more.
For WV-CU161C, hold down the [4] and [6] keys
simultaneously for 2 seconds or more.
The screen is restored to the PIX OFF menu, the
blemish compensation position is deleted and (*) is
also deleted from the right of the number.
• To Restore the Camera Default Position
(REFRESH)
Move the cursor to REFRESH with the joystick and
press the F3 button of WV-CU650.
** SPECIAL2 **
CHROMA GAIN
AP GAIN
PEDESTAL
RESOLUTION
DNR
PIX OFF
REFRESH
CAMERA RESET
RET
For WV-RM70, hold down the right and left buttons
simultaneously for 2 seconds or more.
For WV-CU161C, hold down the [4] and [6] keys simul-
taneously for 2 seconds or more.
• Camera Resetting (CAMERA RESET)
Move the cursor to CAMERA RESET with the joystick
and press the F4 button of WV-CU650.
** SPECIAL2 **
CHROMA GAIN
AP GAIN
PEDESTAL
RESOLUTION
DNR
PIX OFF
REFRESH
CAMERA RESET
RET
+
••••
••••
+
|
••••
••••
+
|
•••••••
+
|
NORMAL
LOW2
→ PUSH SET
→ PUSH SET
••••
••••
+
|
••••
••••
+
|
•••••••
+
|
NORMAL
LOW2
→ PUSH SET
→ PUSH SET
The camera is reset to the factory default settings.
(However, the edited settings for PRESET MENU, AUTO
PAN, PATROL (SPECIAL 1), PIX OFF (SPECIAL 2) and
the registered password will not be reset.)
For WV-RM70, hold down the right, left and set switches
simultaneously for 2 seconds or more. For WV-CU161C,
hold down the [4], [5] and [6] keys simultaneously for 2
seconds or more.
The ALL RESET indication will be displayed.
Note:
In case of performing this operation on the condition
that the cursor is positioned on other than CAMERA
RESET, you cannot perform the operations on the
menu thereafter. In that event, set the camera menu
to ON again with the controller referring to page 26.
• To Close the SPECIAL2 Menu
Move the cursor to RET and press the CAM (SET) but-
ton.
The setup menu appears on the monitor screen.
CHROMA GAIN
AP GAIN
PEDESTAL
RESOLUTION
DNR
PIX OFF
REFRESH
CAMERA RESET
RET
Reset to the Factory Default Settings
Any of the above settings plus the ALC/MANUAL level
control and phase adjustments can be reset to the fac-
tory default settings by placing the cursor over the
desired mode and then pressing the F3 button of WV-
CU650.
For WV-RM70, hold down the right and left switches
simultaneously for 2 seconds or more.
For WV-CU161C, hold down the [4] and [6] keys simul-
taneously for 2 seconds or more.
-50-
** SPECIAL2 **
••••
••••
+
|
••••
••••
+
|
•••••••
+
|
NORMAL
LOW2
→ PUSH SET
→ PUSH SET

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Wv-cs574e

Table des Matières