RugDoctor PRO Deep Carpet Cleaner PDC-1 Mode D'emploi page 7

CLEANING AND STORING MACHINE
1
Clean & Rinse Water Tanks
Press Dirty Water Tank and Clean Water Tank
Release Buttons and pull tanks outward.
Carry tanks
to the sink
and rinse
both tanks
out with
warm water.
Allow tanks
to dry
thoroughly to
prevent odor
when stored.
3
Wrap the Cord
Wrap the cord
around the
Rotating Cord
Wrap.
REMOVEABLE BRUSH ROLL
1. Turn off machine and unplug the
machine from the power outlet.
2. Remove tanks.
3. Place machine on the side to allow
access to Brush Roll access panel.
4. Remove four screws located on the
brush roll panel.
12
PART #71498 R U G D O C T O R P R O D E E P C A R P E T C L E A N E R
FILE NAME RUGDOC_12336-1_MANUAL UPDATE
>>
CLIENT RUGDOC
>>
JOB NUMBER 12336
>>
MANUAL
ELEMENT
>>
ACCOUNT
>>
KP
PRODUCTION ARTIST
>>
LOOMIS is releasing this file as requested for release noted below. We are relinquishing all responsibility for the completion of the project and the Agency will be held harmless for any
error, oversights, omissions or other issues that may subsequently arise during the course of completion for this project.
2
Secure Water Tanks
After rinsing and drying
both tanks, place both
tanks onto machine and
lock in place.
4
Fold Handle
Pull up the Fold
Handle Release
button to fold down
handle for easy and
quick storage.
5. Lift Brush Roll through side of machine.
6. Insert and slide in clean Brush Roll.
7. Replace Brush Roll access panel and
secure with screws.
8. Place machine upright and replace tanks.
| U s e r M a n u a l
BLEED .9" X 11.5"
>>
TRIM 8.5" X 11"
>>
N/A"
LIVE
>>
4/4
COLOR
>>
1" = 1"
SCALE
>>
TROUBLESHOOTING
The following Troubleshooting guide is provided to help you resolve issues
that may arise with common usage of the machine.
PROBLEM POSSIBLE REASON
›
Power cord not plugged in
No Power
›
Power Button not turned on
Pulling handle back
›
Handle is in locked position
lifts front of machine
›
Not pressing Soap & Scrub Solution
Button
›
Clean Water Tank is empty or low
›
Clean Water Tank is not seated
No / Low Spray
or installed correctly
›
Power Button is in the incorrect
position
›
Valve of Clean Water Tank is clogged
›
Dirty Water Tank Is full
›
Dirty Water Tank is not seated /
installed correctly
›
Easy Lift Caddy is not installed
No / Low Suction correctly
›
Power Button is in the incorrect
position
›
Vacuum Hose Port on the Dirty
Water Tank is not fully sealed
›
Not Pressing Soap and Scrub Solution
Button
›
Machine is not the Carpet mode
Rotating Brush Roll
Doesn't Rotate
›
If something is lodged in the Brush
Roll, Brush Roll will stop rotating
and Brush Jam Indicator Light
will turn on
If you are not able to resolve or have other questions, call the customer service hotline at 1-800-784-3628.
r u g d o c t o r . c o m | 1 - 8 0 0 - 7 8 4 - 3 6 2 8
HOW TO FIX
›
Plug power cord into wall outlet
›
Push Power Button to Carpet or Tool
depending on need
›
While pressing Easy Lift Tank Caddy down,
pull straight back on the Main Handle to
release Main Handle into cleaning position
›
Press and hold Soap & Scrub Solution Button
›
Fill Clean Water Tank with water and solution
›
Lift up Clean Water Tank, and place back into
position. Tank should click into place when
positioned properly
›
Verify that the Power button is in the correct
position depending on usage
›
Remove valve from bottom of Clean Water Tank.
Clean with warm soapy water and replace
›
Empty Dirty Water Tank and replace empty
tank when finished
›
Lift up Dirty Water Tank and place back
into position
›
Please refer to page 10, Easy Lift Caddy section,
to re-install the Easy Lift Caddy.
›
Double check the Power Button, and
ensure it is on the desired mode (Carpet
is for carpet cleaning; Tool is for powered,
optional accessories)
›
Press the black flap into the Vacuum Hose Port
tightly
›
Press Soap and Scrub Solution Button on Handle
›
Push Power Button to Carpet
›
Turn machine off and unplug power cord from
outlet. Check that there is nothing stopping
the Brush Roll from rotating. When the Brush
Roll jam has been cleared, plug in the machine
and turn the machine on to reset the Brush Roll
13